JVC HR-DD865EK setup guide Auto SP→LP Timer, Auto Timer, Next Function Memory

Auto SP→LP Timer

If, when timer-recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode to allow complete recording.

For Example . . .

Recording a programme of 210 minutes in length onto a 180- minute tape

Approximately 150 minutes	Approximately 60 minutes
SP mode	LP mode

Total 210 minutes

Make sure you set "AUTO SP→LP TIMER" to "ON" at the Mode Set screen before the timer-recording starts.

	ACCESS MAIN MENU
1	SCREEN
	Press MENU.
	ACCESS MODE SET
2	SCREEN
	Press %Þ to move the highlight bar (pointer) to "MODE
	SET", then press OK or #.
3	SELECT MODE
	Press %Þ to move the	MODE SET
	highlight bar (pointer) to	B. E. S. T.	ON
	"AUTO SP→LP TIMER",
		PICTURE CONTROL	AUTO
	then press OK or #to select	AUTO TIMER	OFF
	"ON".	O. S. D.	ON
		DIRECT REC	ON
		AUTO SP=LP TIMER	ON
		POWER SAVE	OFF
		NEXT PAGE
		[5°] =
		[MENU] : EXIT
	RETURN TO NORMAL
4	SCREEN
	Press MENU.

NOTES:

●The Auto SP→LP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly with any tapes longer than E-180 or with some tapes of shorter lengths.

●If you have programmed the recorder to timer-record 2 or more

programmes, the second programme and those thereafter may not fit on the tape if you set "AUTO SP→LP TIMER" to "ON". In this case, make sure the mode is not engaged, then set the tape speed manually during timer programming.

●In order to ensure that the recording fits on the tape, this feature may leave a short non-recorded section at the end of the tape.

●There may be some picture noise and sound disturbance at the point on the tape where the recorder switches from SP to LP mode.

●If you perform timer recording with both PDC and the Auto SP→LP Timer activated, and the programme goes beyond its originally scheduled length, there may be times when the programme cannot be recorded in its entirety.

43

Auto Timer

When the Auto Timer is set to ON the timer is automatically engaged when the recorder power is turned off and automati- cally disengaged when the recorder is powered back on.

	ACCESS MAIN MENU
1	SCREEN
	Press MENU.
2	ACCESS MODE SET SCREEN
	Press %Þ to move the		MAIN MENU
	highlight bar (pointer) to
	"MODE SET", then press		MODE SET
			AUTO CH SET
	OK or #.		MANUAL CH SET
			INITIAL SET
			REC LEVEL CTL
		[5°] =
			[MENU] : EXIT
3	SELECT MODE
	Press OK or #to select		MODE SET
	either "ON" or "OFF".		B. E. S. T.	ON
			PICTURE CONTROL	AUTO
			AUTO TIMER	ON
			O. S. D.	ON
			DIRECT REC	ON
			AUTO SP=LP TIMER	OFF
			POWER SAVE	OFF
			NEXT PAGE
		[5°] =
			[MENU] : EXIT
	RETURN TO NORMAL
4	SCREEN
	Press MENU.

NOTE:

For safety, when Auto timer is set to "OFF", all other recorder functions are disabled while the Timer mode is engaged. To disengage the timer, press ä (TIMER).

Next Function Memory

The Next Function Memory "tells" the recorder what to do after rewinding. Before continuing, make sure the recorder is in the Stop mode.

a– For Automatic Start Of Playback After Tape Rewind . . .

. . . press REW, then press PLAY within 2 seconds. b– For Automatic Power Off After Tape Rewind . . .

. . . press REW, then press within 2 seconds.

c– For Automatic Timer Standby After Tape Rewind . . .

. . . press REW, then press (TIMER) within 2 seconds.