JVC HR-DD865EK setup guide Before performing the following steps, Pressing %Þ, then press OK or #

Page 29

29

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 IN/DECODER connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

●Auto Satellite Prog recording and timer-recording cannot be done at the same time.

●When you press and hold the recorder's REC LINK button to engage the Auto Satellite Prog Rec mode, if the REC LINK button does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*.

If this is the case, perform "Express Timer Programming" (☞ pg. 16) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder's AV2 IN/DECODER connector. (☞ pg. 28)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

ACCESS MAIN MENU SCREEN

1 Press MENU.

 

 

 

 

 

 

ACCESS MODE SET SCREEN

 

 

 

Move the highlight bar (pointer) to "MODE SET" by

2 pressing %Þ, then press OK or #.

 

 

3

SELECT AV2 SELECT MODE

 

 

Move the highlight bar (pointer) to "AV2 SELECT", by

pressing %Þ, then press OK or #to set to "SAT".

 

 

 

MODE SET

 

 

PREVIOUS PAGE

 

 

 

 

 

 

 

 

 

 

 

B. E. S. T.

ON

 

AV2 SELECT

SAT

 

 

 

PICTURE CONTROL

AUTO

 

TIME SCAN AUDIO

ON

 

 

 

AUTO TIMER

OFF

 

 

 

 

 

O. S. D.

ON

 

 

 

 

 

DIRECT REC

ON

 

 

 

 

 

AUTO SP=LP TIMER

OFF

 

 

 

 

 

POWER SAVE

OFF

 

 

 

 

 

NEXT PAGE

 

 

 

 

 

 

[5°] =

 

 

[5°] =

 

 

 

 

[MENU] : EXIT

 

 

[MENU] : EXIT

 

 

 

 

 

 

 

 

 

 

SET TAPE SPEED

 

 

 

4 Press SP/LP ( ) to set the tape speed.

 

 

 

ENGAGE AUTO SATELLITE PROG

5

REC MODE

 

 

 

 

 

Press and hold REC LINK for about 2 seconds. The

 

 

button lights up and the recorder turns off automatically.

 

 

 

 

●To disengage the Auto Satellite Prog Rec mode, press REC LINK. The light goes off.

●If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

NOTES:

●Auto Satellite Prog recording is possible with the AV2 IN/DECODER connector only.

●When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

●After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function (☞ pg. 23).

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.

●The REC LINK button blinks while Auto Satellite Prog recording is in progress.

●Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode.

●If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 4 will apply to all the programmes for Auto Satellite Prog recording.

●The B.E.S.T. system (☞ pg. 20) does not work while Auto Satellite Prog recording is in progress.

●Just Clock (☞ pg. 55) does not work when the Auto Satellite Prog Rec mode is engaged.

●Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK button blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 IN/DECODER connector.

Page 28 Page 30
Image 29
Page 28 Page 30
Contents HR-DD865EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide AV input connector Scart To connect to a TV with 21-pin AV input connector ScartBack of TV TV Aerial Cable not providedYour TV via both an RF cable and a 21-pin If you have connected the video recorder toBeginningEnd Go to itemPress OK to exit Video Channel Set mode Remote control while downloading is8 or If -- appears on the display panel, refer Link screen will appear. Then the GuideIf auto channel set has succeeded but auto clock set has not Link Functions TV Auto Power OnTurn on the Recorder NexTView LinkLoad a Cassette PlaybackPoint Start PlaybackStill Picture/Frame-By-Frame Playback Activate HIGH-SPEED SearchSlow Motion High-Speed Turbo SearchRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Access Main Menu Screen Adjust TrackingAccess Mode SET Screen SET ModeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsOr press Record on the recorder RecordingPlayback Activate Index Search Looking For Scene You WantSkip Over Unwanted SectionsInstant ReView Activate InstantReview Variable-Speed Search/ Reverse Play TimeScanNormal recorder VisibleNoiselessMove the highlight bar pointer to Time Scan Audio TimeScanSpeed SP Speed LP Audio output Selecting Sound You Want Access Main MenuControl Screen Hi-Fi Audio Recording Level ControlType of Broadcast On-screen Display Being Received Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Automatic Satellite Programme Recording Aerial connectorSatellite Receiver Unit AerialBefore performing the following steps Move the highlight bar pointer to Mode SET byPressing %Þ, then press OK or # Move the highlight bar pointer to AV2 SELECT, byRE-SUPPLY Power SET Remote ControlRemote A/B Code Switching Remote Con- trol FunctionsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVTV Prog +/-,NUMBER keys Satellite Receiver Multi- Brand Remote ControlOperate Satellite Receiver Edit From Camcorder Repeat steps 4 6 as necessary ConnectorSynchro Editing Edit To Or From Another Video Recorder Input ModeSET Recording DECK’S Start Source PlayerAV2 Select Setting Locate Start Point SET Input ModeEngage Audio Dubbing Start DubbingLocate END Point Reset the CounterInsert Editing END Insert Editing Engage Insert EditingStart Editing Information On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorTerminal Press OK orENABLE/DISABLE Access Mode SETOther Functions ON-SCREEN DisplayPower SAVE, then press Power Save ModeNext Function Memory Auto SP→LP TimerAuto Timer Resume Recording Engage RECORD-PAUSE ModeRepeat Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalAuto Channel Set Tuner SetPerform Auto Channel SET After Scan Completed Screen preset positionsIs displayed on the screen For about 5 seconds, aStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Switch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List Channel Islands TV Station Channel Number GuideJust Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Playback Questions And AnswersTroubleshooting Won’t stop Timer RecordingFront View IndexRear View Remote Control How To Use Remote Control LCDVHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical
Top Page Image Contents