JVC HR-DD865EK setup guide Synchro Editing, Repeat steps 4 6 as necessary, Connector

Page 34

Press NUMBER key “0” and/or TV PROG so that “F-1” appears in place of a preset position number.

SET EDIT MODE

See "Picture Control" on page 19.

LOCATE START POINT

Start playback of the tape in the camcorder, and pause playback when you find the point where you want to start editing. Press and hold PAUSE and press RECORD on your recorder so that the recorder enters the Record- Pause Mode.

START SYNCHRO EDITING

Press SYNCHRO EDIT.

PAUSE SYNCHRO EDITING

2

3

4

Connect your recorder to camcorder (☞ pg. 33), and connect your recorder's SYNCHRO EDIT connector to the camcorder's LANC connector.

SET RECORDER'S INPUT MODE

1

The Synchro Editing function synchronizes the start of the playback and recording operations when starting an edit operation using a camcorder equipped with a LANC connector and your video recorder.

MAKE CONNECTIONS

ADVANCED OPERATIONS (cont.)

34

Synchro Editing

PAUSE

SYNCHRO	EDIT	RECORD

1– –:– –

2

1 2 3

4 5 6

7 8 9

NUMBER "0" 0

1

2

3

4

4

3

TV PROG

5

6 Press SYNCHRO EDIT again.

●Repeat steps 4 – 6 as necessary.

Recorder

SYNCHRO EDIT

JLIP

ANT. IN

AV1 IN/OUT	L
	AUDIO
	OUT
	R
AV2 IN/DECODER	PAUSE
	RF OUT

SYNCHRO EDIT

connector

LANC Cable (not provided)

Player

Camcorder

To LANC connector

NOTES:

●The Synchro Edit function may not work with the initial part of a camcorder tape.

●The Synchro Edit function cannot be used when using the JLIP function. (Pressing SYNCHRO EDIT cancels the JLIP function.)

●The Synchro Editing function may not work properly with some type of camcorder.

●When you select EDIT to dub tapes in step 3, be sure to select AUTO (or NORM when B.E.S.T. is set to OFF) after you finish dubbing the tapes.

Image 34

Contents HR-DD865EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV To connect to a TV with 21-pin AV input connector ScartAV input connector Scart TV Aerial Cable not providedBeginningEnd If you have connected the video recorder toYour TV via both an RF cable and a 21-pin Go to item8 or If -- appears on the display panel, refer Remote control while downloading isPress OK to exit Video Channel Set mode Link screen will appear. Then the GuideIf auto channel set has succeeded but auto clock set has not Turn on the Recorder TV Auto Power OnLink Functions NexTView LinkPoint PlaybackLoad a Cassette Start PlaybackSlow Motion Activate HIGH-SPEED SearchStill Picture/Frame-By-Frame Playback High-Speed Turbo SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Access Mode SET Screen Adjust TrackingAccess Main Menu Screen SET ModePlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemPlayback RecordingOr press Record on the recorder Skip Over Unwanted Looking For Scene You WantActivate Index Search SectionsReview Activate InstantInstant ReView Normal recorder TimeScanVariable-Speed Search/ Reverse Play VisibleNoiselessSpeed SP Speed LP Audio output TimeScanMove the highlight bar pointer to Time Scan Audio Control Screen Access Main MenuSelecting Sound You Want Hi-Fi Audio Recording Level ControlSoundtrack Selection Receiving Nicam Stereo And Bilingual ProgrammesType of Broadcast On-screen Display Being Received Satellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording AerialPressing %Þ, then press OK or # Move the highlight bar pointer to Mode SET byBefore performing the following steps Move the highlight bar pointer to AV2 SELECT, byRemote A/B Code Switching SET Remote ControlRE-SUPPLY Power Remote Con- trol FunctionsSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Operate TVOperate Satellite Receiver Satellite Receiver Multi- Brand Remote ControlTV Prog +/-,NUMBER keys Edit From Camcorder Synchro Editing ConnectorRepeat steps 4 6 as necessary SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Start Source PlayerAV2 Select Setting Engage Audio Dubbing SET Input ModeLocate Start Point Start DubbingInsert Editing Reset the CounterLocate END Point Start Editing Engage Insert EditingEND Insert Editing Terminal Terminal JLIPJoint Level Interface Protocol ConnectorInformation On J Terminal Press OK orOther Functions Access Mode SETENABLE/DISABLE ON-SCREEN DisplayPower Save Mode Power SAVE, then pressAuto Timer Auto SP→LP TimerNext Function Memory Repeat Playback Engage RECORD-PAUSE ModeResume Recording RetakeConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionPerform Auto Channel SET Tuner SetAuto Channel Set Is displayed on the screen Screen preset positionsAfter Scan Completed For about 5 seconds, aStoring Channels Manually Fine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Channel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Channel IslandsClock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Questions And Answers PlaybackTroubleshooting Timer Recording Won’t stopIndex Front ViewRear View Remote Control Remote Control LCD How To UseDA4 Double Azimuth helical Maximum recording timeVHF 44.5 143/143 470 MHz