JVC HR-DD865EK setup guide Back of TV, TV Aerial Cable not provided, Back of Recorder

Page 5

5

STEP

2

INSTALLATION

CONNECT VIDEO RECORDER TO TV

Place the recorder on a stable, flat surface.

Back of TV

Aerial connector

21-pin AV input connector (SCART)

Mains Power Cord

Mains outlet

RF Cable (provided)

21-pin SCART Cable (not provided)

Make this connection if your TV has a

21-pin AV input connector (SCART) in order to reduce the possibility of interference. And if you are using a stereo TV, you will need this cable in order to enjoy stereo playback of videotapes.

SYNCHRO EDIT

AV1 IN/OUT

L

AUDIO

OUT

R

AV2 IN/DECODER

PAUSE

RF OUT

JLIP

ANT. IN

TV Aerial Cable (not provided)

Back of Recorder

RF CONNECTION

To connect to a TV with NO 21-pin AV input connector (SCART) . . .

1– Disconnect the TV aerial cable from the TV.

2– Connect the TV aerial cable to the ANT. IN jack on the rear panel of the recorder.

3– Connect the provided RF cable between the RF OUT jack on the rear panel of the recorder and the TV’s aerial connector.

AV CONNECTION

To connect to a TV with 21-pin AV input connector (SCART) . . .

1– Connect the aerial, recorder and TV as per “RF CONNECTION”. 2– Connect an optional SCART cable between the AV1 IN/OUT socket on the rear panel of the recorder and the TV’s 21-pin

AV input connector (SCART).

ATTENTION

■Do NOT Plug the mains power cord into a mains outlet until all connections are completed.

■Do NOT press the button on the recorder or on the remote control to turn on the recorder's power before you start the Auto Set Up procedure described on page 6.

AFTER YOU FINISH THIS STEP

Go to Step 3 – AUTO SET UP

Image 5

Contents HR-DD865EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide AV input connector Scart To connect to a TV with 21-pin AV input connector ScartBack of TV TV Aerial Cable not providedYour TV via both an RF cable and a 21-pin If you have connected the video recorder toBeginningEnd Go to itemPress OK to exit Video Channel Set mode Remote control while downloading is8 or If -- appears on the display panel, refer Link screen will appear. Then the GuideIf auto channel set has succeeded but auto clock set has not Link Functions TV Auto Power OnTurn on the Recorder NexTView LinkLoad a Cassette PlaybackPoint Start PlaybackStill Picture/Frame-By-Frame Playback Activate HIGH-SPEED SearchSlow Motion High-Speed Turbo SearchRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Access Main Menu Screen Adjust TrackingAccess Mode SET Screen SET ModeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsOr press Record on the recorder RecordingPlayback Activate Index Search Looking For Scene You WantSkip Over Unwanted SectionsInstant ReView Activate InstantReview Variable-Speed Search/ Reverse Play TimeScanNormal recorder VisibleNoiselessMove the highlight bar pointer to Time Scan Audio TimeScanSpeed SP Speed LP Audio output Selecting Sound You Want Access Main MenuControl Screen Hi-Fi Audio Recording Level ControlType of Broadcast On-screen Display Being Received Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Automatic Satellite Programme Recording Aerial connectorSatellite Receiver Unit AerialBefore performing the following steps Move the highlight bar pointer to Mode SET byPressing %Þ, then press OK or # Move the highlight bar pointer to AV2 SELECT, byRE-SUPPLY Power SET Remote ControlRemote A/B Code Switching Remote Con- trol FunctionsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVTV Prog +/-,NUMBER keys Satellite Receiver Multi- Brand Remote ControlOperate Satellite Receiver Edit From Camcorder Repeat steps 4 6 as necessary ConnectorSynchro Editing Edit To Or From Another Video Recorder Input ModeSET Recording DECK’S Start Source PlayerAV2 Select Setting Locate Start Point SET Input ModeEngage Audio Dubbing Start DubbingLocate END Point Reset the CounterInsert Editing END Insert Editing Engage Insert EditingStart Editing Information On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorTerminal Press OK orENABLE/DISABLE Access Mode SETOther Functions ON-SCREEN DisplayPower SAVE, then press Power Save ModeNext Function Memory Auto SP→LP TimerAuto Timer Resume Recording Engage RECORD-PAUSE ModeRepeat Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalAuto Channel Set Tuner SetPerform Auto Channel SET After Scan Completed Screen preset positionsIs displayed on the screen For about 5 seconds, aStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Switch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List Channel Islands TV Station Channel Number GuideJust Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Playback Questions And AnswersTroubleshooting Won’t stop Timer RecordingFront View IndexRear View Remote Control How To Use Remote Control LCDVHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical