JVC HR-DD865EK setup guide Connection To Stereo System, Audio Cable not provided Speaker

Page 45

SYSTEMCONNECTIONS45

Connection To

AStereo System

These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.

FM Tuner

CD Player

Stereo Amplifier

I I I I	I	II
		I
		II
		II

I

I

I

I

I

I

I

I

AUX IN or TAPE MONITOR

Speaker

Television

Audio Cable (not provided)

Speaker

SYNCHRO EDIT

AV1 IN/OUT

L

AUDIO

OUT

R

AV2 IN/DECODER

PAUSE

RF OUT

Mains outlet

JLIP

ANT. IN

Back of Recorder

AUDIO OUT

MAKE CONNECTIONS

1 Connect the AUDIO OUT L and R connectors on your video recorder to the AUX IN or TAPE MONITOR terminals on your stereo system's receiver or amplifier.

NOTES:

●When connecting your recorder's audio output connectors to a stereo amplifier, make sure you connect L and R correctly.

●If you can receive NICAM TV broadcasts in your area, this recorder can record them independently of the TV set and play them back through the connected stereo system.

●When listening to sound through the connected stereo system, turn the TV's volume down completely.

CAUTIONS:

●This recorder has a dynamic range of more than 80 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them.

●Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the video playback picture.

Image 45

Contents HR-DD865EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide AV input connector Scart To connect to a TV with 21-pin AV input connector ScartBack of TV TV Aerial Cable not providedYour TV via both an RF cable and a 21-pin If you have connected the video recorder toBeginningEnd Go to itemPress OK to exit Video Channel Set mode Remote control while downloading is8 or If -- appears on the display panel, refer Link screen will appear. Then the GuideIf auto channel set has succeeded but auto clock set has not Link Functions TV Auto Power OnTurn on the Recorder NexTView LinkLoad a Cassette PlaybackPoint Start PlaybackStill Picture/Frame-By-Frame Playback Activate HIGH-SPEED SearchSlow Motion High-Speed Turbo SearchRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Access Main Menu Screen Adjust TrackingAccess Mode SET Screen SET ModeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsRecording PlaybackOr press Record on the recorder Activate Index Search Looking For Scene You WantSkip Over Unwanted SectionsActivate Instant ReviewInstant ReView Variable-Speed Search/ Reverse Play TimeScanNormal recorder VisibleNoiselessTimeScan Speed SP Speed LP Audio outputMove the highlight bar pointer to Time Scan Audio Selecting Sound You Want Access Main MenuControl Screen Hi-Fi Audio Recording Level ControlReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionType of Broadcast On-screen Display Being Received Automatic Satellite Programme Recording Aerial connectorSatellite Receiver Unit AerialBefore performing the following steps Move the highlight bar pointer to Mode SET byPressing %Þ, then press OK or # Move the highlight bar pointer to AV2 SELECT, byRE-SUPPLY Power SET Remote ControlRemote A/B Code Switching Remote Con- trol FunctionsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlSET TV Brand Code Operate TVSatellite Receiver Multi- Brand Remote Control Operate Satellite ReceiverTV Prog +/-,NUMBER keys Edit From Camcorder Connector Synchro EditingRepeat steps 4 6 as necessary Edit To Or From Another Video Recorder Input ModeSET Recording DECK’S Start Source PlayerAV2 Select Setting Locate Start Point SET Input ModeEngage Audio Dubbing Start DubbingReset the Counter Insert EditingLocate END Point Engage Insert Editing Start EditingEND Insert Editing Information On J Terminal Terminal JLIPJoint Level Interface Protocol ConnectorTerminal Press OK orENABLE/DISABLE Access Mode SETOther Functions ON-SCREEN DisplayPower SAVE, then press Power Save ModeAuto SP→LP Timer Auto TimerNext Function Memory Resume Recording Engage RECORD-PAUSE ModeRepeat Playback RetakeAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalTuner Set Perform Auto Channel SETAuto Channel Set After Scan Completed Screen preset positionsIs displayed on the screen For about 5 seconds, aStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Switch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List Channel Islands TV Station Channel Number GuideJust Clock Clock SetVideo Plus+ Setup NumberGuide Program Number Set Playback Questions And AnswersTroubleshooting Won’t stop Timer RecordingFront View IndexRear View Remote Control How To Use Remote Control LCDMaximum recording time DA4 Double Azimuth helicalVHF 44.5 143/143 470 MHz