JVC HR-DD865EK setup guide Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 46

46SUBSIDIARYSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

STOP

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 6).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.

●If you have connected the video recorder to your TV via both the provided RF cable and a

21-pin SCART cable (AV connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV Connection" below.

●If you have connected the video recorder to your TV via the provided RF cable only (RF connection), you have to set the correct video channel — Go to "With RF Connection" on page 47.

With AV Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL SET MODE

1

2

1

2

– –:– –

1 2 3

4 5 6

7 8 9

0

3

4

4

3 OK

TV PROG

1	Press and hold down STOP on the recorder until the
	display panel shows the following.


2	SET VIDEO CHANNEL
	Press TV PROG – until the display panel shows
	"–OUT– –".

●Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 46

Contents HR-DD865EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV To connect to a TV with 21-pin AV input connector ScartAV input connector Scart TV Aerial Cable not providedBeginningEnd If you have connected the video recorder toYour TV via both an RF cable and a 21-pin Go to item8 or If -- appears on the display panel, refer Remote control while downloading isPress OK to exit Video Channel Set mode Link screen will appear. Then the GuideIf auto channel set has succeeded but auto clock set has not Turn on the Recorder TV Auto Power OnLink Functions NexTView LinkPoint PlaybackLoad a Cassette Start PlaybackSlow Motion Activate HIGH-SPEED SearchStill Picture/Frame-By-Frame Playback High-Speed Turbo SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Access Mode SET Screen Adjust TrackingAccess Main Menu Screen SET ModePlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemPlayback RecordingOr press Record on the recorder Skip Over Unwanted Looking For Scene You WantActivate Index Search SectionsReview Activate InstantInstant ReView Normal recorder TimeScanVariable-Speed Search/ Reverse Play VisibleNoiselessSpeed SP Speed LP Audio output TimeScanMove the highlight bar pointer to Time Scan Audio Control Screen Access Main MenuSelecting Sound You Want Hi-Fi Audio Recording Level ControlSoundtrack Selection Receiving Nicam Stereo And Bilingual ProgrammesType of Broadcast On-screen Display Being Received Satellite Receiver Unit Aerial connectorAutomatic Satellite Programme Recording AerialPressing %Þ, then press OK or # Move the highlight bar pointer to Mode SET byBefore performing the following steps Move the highlight bar pointer to AV2 SELECT, byRemote A/B Code Switching SET Remote ControlRE-SUPPLY Power Remote Con- trol FunctionsSET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Operate TVOperate Satellite Receiver Satellite Receiver Multi- Brand Remote ControlTV Prog +/-,NUMBER keys Edit From Camcorder Synchro Editing ConnectorRepeat steps 4 6 as necessary SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Start Source PlayerAV2 Select Setting Engage Audio Dubbing SET Input ModeLocate Start Point Start DubbingInsert Editing Reset the CounterLocate END Point Start Editing Engage Insert EditingEND Insert Editing Terminal Terminal JLIPJoint Level Interface Protocol ConnectorInformation On J Terminal Press OK orOther Functions Access Mode SETENABLE/DISABLE ON-SCREEN DisplayPower Save Mode Power SAVE, then pressAuto Timer Auto SP→LP TimerNext Function Memory Repeat Playback Engage RECORD-PAUSE ModeResume Recording RetakeConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionPerform Auto Channel SET Tuner SetAuto Channel Set Is displayed on the screen Screen preset positionsAfter Scan Completed For about 5 seconds, aStoring Channels Manually Fine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Channel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Channel IslandsClock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Questions And Answers PlaybackTroubleshooting Timer Recording Won’t stopIndex Front ViewRear View Remote Control Remote Control LCD How To UseDA4 Double Azimuth helical Maximum recording timeVHF 44.5 143/143 470 MHz