JVC HM-DH5U manual Input/Output settings IN/OUT Function

Filename [HM-DH5U_Eng.fm]

HM-DH5U_Eng.fm Page 65 Wednesday, June 2, 2004 12:44 PM Masterpage:Right-FullCol

EN 65

Input/Output settings “ IN/OUT FUNCTION”

		*The default setting is bold in the table below.
L “TV OUTPUT 1”	Select the appropriate mode depending on the type of TV you have.
“WIDE 16:9”	“WIDE 16:9”	: Select this for a wide TV set with 16:9 screen image size.
“NORMAL 4:3”	“NORMAL 4:3” : Select this for a TV set with 4:3 screen image size.
	NOTES:
	• When “TV OUTPUT 1” is set to “WIDE 16:9”, sometimes the screen image may be stretched vertically.
	• When “TV OUTPUT 1” is set to “NORMAL 4:3”, sometimes subtitles may not be visible or the ends of the
	screen image may be cut off. Normally select “WIDE16:9”.
	• In order to let the equipment determine the screen image size, it is recommended that you connect the VCR
	and TV using the [COMPONENT VIDEO OUTPUT] connectors or [S VIDEO OUTPUT] connector.
	• This function is invalid if HDMI is activated.
L “TV OUTPUT 2”	Select the appropriate mode when receiving signals via i.LINK connector or playing
“720to1080”	back a D-VHS tape containing a recording of an HD (High Definition) signal.
“NO CONV.”	“720to1080”	: 720p is up-converted to 1080i and output to the TV. 1080i, 480p, and
“ALLto480i”		480i image formats are output to the TV without being converted.
“ALLto480p”		Select this when the 720p image played back is distorted.
	“NO CONV.” : 1080i, 720p, 480p, and 480i image formats are output to the TV
		just as they are.
	“ALLto480i”	: All images will be output to the TV in 480i image format.
	“ALLto480p”	: All images will be output to the TV in 480p image format.
	NOTES:
	• When you receive signals via i.LINK connector or play back the picture of 1080i, 720p, 480p
	image format, the signal is not output from the [S-VIDEO] or [VIDEO] output connector if “TV
	OUTPUT 2” is set to “720to1080” or “NO CONV.”.
	• The progressive mode indicator [q] on the front display panel will light up when “ALLto480p” is
	selected.
	• If your TV supports only 480i image format and “ALLto480p” mode is previously selected, you
	can forcibly change the mode to “ALLto480i” by pressing and holding [PAUSE (W)] on the front
	panel for more than 5 seconds during power off mode.
	• During DV input, the image format output to the TV will be 480i even if this function is set to
	“ALLto480p”. However, the menu setting is retained and changes can be made.
	• If you cannot see the pictures on the TV screen when you play back a tape, set “TV OUTPUT 2”
	to the appropriate mode.
	• This function is invalid if HDMI is activated.
L “480i to 480p”	When this function is set to “ON”, progressive output is being selected. The 480i image
“ON”	format is up-converted to 480p and output to the TV. The progressive mode indicator
“OFF”	[q] on the front display panel will light up.
	NOTES:
	• When “TV OUTPUT 2” is set to “ALLto480i”, the image format being output to the TV will be
	480i even if this function is set to “ON”.
	• During DV input, the image format output to the TV will be 480i even if this function is set to
	“ON”. However, the menu setting is retained and changes can be made. If you are using a TV
	with DVI input, and it does not support 480i image format, use the TV’s analog input instead.
	• This function is invalid if HDMI is activated.
L “HDMI to DVI	When this VCR is connected to the TV via the DVI connection through [HDMI OUT]
COLOR”	connector, this function allows you to select the desired deeper color intensity and to
“STANDARD”	tone down the black color of the picture.
“ENHANCE”
L “HDMI OUTPUT”	Set this function to “RGB FIX” when the output from the [HDMI OUT] connector cannot
“AUTO”	be properly displayed on the TV screen.
“RGB FIX”
L “FRONT AUX F-1”	You have to select which terminal - either [VIDEO] (composite) or [S-VIDEO] (Y/C
“VIDEO”	separate signals) to use as the video input terminal on the front panel.
“S-VIDEO”	Make sure to select the correct terminal; otherwise, you may fail in recording (editing)
	on this VCR.