MicroBoards Technology HCL-4000, HCL Series, HCL-6000, HCL-8000 user manual Pass 100 Fail

Page 15

MICROBOARDS TECHNOLOGY, LLC

HCL Series

The loader will continue to remove discs from the input spindle and place those into drives until either all of the drives are full, or the count that you loaded into the counter is reached.

Processing...

Please Wait

It takes a few seconds for the autoloader to recognize all the discs.

After two or three seconds of processing time, one of the following Copy Progress screens will appear.

Copying...

H4012MB

0/21

12%

¾“H” indicates the source of the job resides in the Hard Drive.

¾“4012MB” indicates the capacity of the master disc.

¾“12%” indicates the current progress of the duplication.

¾“0/21” indicates you have a project size of 21 copies and you have made 0 copies so far.

or:

Copying... H4012MB

012%

¾“H” indicates the source of the job resides in the Hard Drive.

¾“4012MB” indicates the capacity of the master disc.

¾“12%” indicates the current progress of the duplication.

¾“0” indicates you have made 0 copies so far.

Note: It is normal to see the progress indicator stay at 0%-10% and 100% for approximately 30 seconds for CD duplication and up to one minute for DVD duplication. That is caused by the initializing and finalizing stages.

Loader Processing Drive 1 -> Output Bin

Once the duplication run is completed, the loader will remove the finished disc from the drive and place the successful copy on the Output Spindle. If there are any unsuccessful, they will be placed in the reject area.

The loader will then pick up another blank disc and load it into the drive. This is then repeated for each disc.

Loader Processing Drive 2 <- Input Bin

The copying process will continue until you either run out of blank discs or until the count that you loaded into the counter is reached.

If you run out of blank discs and the job is not complete, the autoloader will give you an opportunity to fill the spindle:

Important: When you add discs to the input spindle, be sure to remove your finished discs from the Output Spindle.

Input Bin Empty(20) Continue?

At this point you can either put more discs on to the input spindle and press the OK button to continue, or press the ESC button to terminate your project.

Once the autoloader is through, you will see the following screen:

PASS 100 FAIL 0

Job Completed! Press OK to Finish

“PASS 100" indicates that you made 100 successful copies. “FAIL 0" indicates that you have no failures for this job.

At the bottom of the screen, you will see the scrolling message: “Job Complete! Press OK to Finish”

Press the OK button once again and you shall see the “Access Log” menu. You can press the OK button one more time to see the log that indicates the number of passes and fails for every drive/tray, or simply press the ESC button to go back to the main menu. It is highly recommended to check the log when your job has an abnormal amount of failures.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents HCL Series Introduction Table of Contents Introduction Introduction Microboards Statement Regarding Improper Duplication Front Panel Controls LCD Control Panel LayoutCopy Menu OverviewDVD+R Compatibility Mode Read Error SkipCD Writing Mode Autocopy EnabledDevice Info Load DefaultUpdate Firmware System InfoSingle Master and Multi Master Modes Single Master ModeMulti Master Mode Batch Mode Introduction to Manage AccountsSetting Counters and Assigning Names Setting CountersCounter Specify Counter Specify Counter 0 OK? DVD1 Editing NamesEdit Partition Name OK? Loading Partition?Microboards B.30 Making Copies in Single Master ModeMaster Mode OperationPass 100 Fail Making Copies in Multi Master Mode OK? Input Bin Empty 20 Press OK to Continue Access Log FilePass 16 Fail DVDDuplication Speeds HDD to CD SpeedHDD to CD Speed Adjusted to Microboards B.30 8. Master ModeMicroboards Copy Erase RW Select Partition Microboards B.30 Copy Hard Drive SetupQuick Erasing Pass 25 FailDelete Partition Load PartitionNew Partition Existing Partition Rename PartitionAdmin Partition InfoPartition Size Setup Language Language English Language Espanol Setup Read Error SkipFormat Hard Drive Buzzer Setup Max Audio, VCD & CDG Max Audio, VCD & CDG SpeedSetup Setup Startup Menu Startup Menu CopyMicroboards B.30 16. Autocopy Setup Screen Saver Screen Saver On Screen Saver OffSetup Counter Counter On Counter Off Setup Autocopy EnabledLoader Processing Drive 2-Input Bin 11.10 DVD+R High Compatibility ModeSetup 10.DVD+R High Compatibility Loader Processing Please WaitCD 21M Data 1 Session 1Trk Insert Disc menuCPU RAM MB SdramPlextor Dvdr PX716 Loader Utilities 1. Drive Alignment Please Select Drive Go? System Utilities 4. Load Default Press OK to ContinueLoader Utilities 3. Disc Separator Drive Alignment Alignment Finished?Alignment Next? Drive Alignment Alignment Next?Microboards B.30 14.Manage Accounts Enter PWD OK? Manage Accounts 1. View User AdminLoader Utilities 4. Z form Maneuver Loader Utilities 5.Alignment ProtectionCreate User Edit User InfoDelete User Manage Accounts Password on Bootup Password on BootupDrives cannot read disc and shows error message TroubleshootingCode Short Description Full Description Error CodesMicroboards TECHNOLOGY, LLC Menu Tree Actual Size 8-drive Packaged Size 8-drive SpecificationsSupported Formats Technical Support
Top Page Image Contents