MicroBoards Technology HCL-4000, HCL Series Drive Alignment Alignment Finished?, Alignment Next?

Page 31

MICROBOARDS TECHNOLOGY, LLC

HCL Series

Drive Alignment Alignment Finished?

The autoloader will pick a disc from the first input spindle, move it to ¼ inch above the drive tray, and hold it there. You will see the Drive Alignment screen:

Check the alignment of the drive trays and press the OK button when you are finished.

Note: If the drive trays are not properly aligned and there is a need to re-align them, please contact Tech Support Service for information regarding setting alignments.

Warning: This function is ONLY for checking the alignment, NOT for setting the alignment. Please do not move the robotic arm with your hands during this process.

When you have finished checking the alignment of the drive(s), the robotic arm will move the disc to the arms top position and hold it there. You will see the Alignment Next menu.

Press the OK button to return back to the Please Select Drive menu. This allows you to complete the alignment checking procedure for each of the installed drives.

If you are through checking the alignment of drives, press the ESC button to go back to the Loader Utility Menu

When the drive alignment checking process is complete, the robotic arm will drop the disc in the Reject Area.

13.2 Spindle Alignment

The Spindle Alignment menu option is used to check the alignment of the spindles to the robotic arm. When the Spindle Alignment function is selected, the system picks a disc from the first input spindle and holds it approximately one inch above the target spindle.

To start the alignment, place a disc on to the first input spindle.

Loader Utilities

2. Spindle Alignment

Please Select Spindle

Spindle 1

Go?

Use the Up or Down button to select the Spindle Alignment menu and press the OK button. The autoloader will proceed to the Please Select Spindle menu.

Use the Up or Down button to select the spindle that you want to check and press the OK button to select it.

The autoloader will pick a disc from the input spindle, move it to one inch above the spindle being aligned, and hold it there. You will see the Spindle Alignment screen:

Warning: This function is ONLY for checking the alignment, NOT for setting the alignment. Please do not move the robotic arm with your hands during this process.

Once you are done, press the OK button. This will send you to the Alignment Next menu

 

Press the OK button to return back to the Please Select Spindle menu.

Spindle Alignment

This allows you to complete the alignment checking procedure for each of

Alignment Next?

the installed spindles.

If you are through checking the alignment of spindles, press the ESC button to go back to the Loader Utility Menu.

Drive Alignment Alignment Next?

When the spindle alignment checking process is complete, the robotic arm will drop the disc in the Reject Area.

13.3 Disc Separator

The Disc Separator option is used to circumvent the disc static and sticky media problem. See Disc Static and Sticky Media on page 5. When this option is enabled, after picking up a disc from the input spindle, the robotic arm stops at the top of it’s travel and then bounces down once, twice, or three times to dislodge discs that are stuck together.

To enable the disc separator function:

Loader Utilities 3. Disc Separator

Use the Up or Down button to select the Disc Separator menu and press the OK button to enter that menu.

Use the Up or Down button to select the separator option from the 4 available: Off, Single Vibration, Double Vibration, or Triple Vibration. Press the OK button to select the option displayed.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents HCL Series Introduction Table of Contents Introduction Introduction Microboards Statement Regarding Improper Duplication Front Panel Controls LCD Control Panel LayoutCopy Menu OverviewDVD+R Compatibility Mode Read Error SkipCD Writing Mode Autocopy EnabledDevice Info Load DefaultUpdate Firmware System InfoSingle Master and Multi Master Modes Single Master ModeMulti Master Mode Batch Mode Introduction to Manage AccountsSetting Counters Setting Counters and Assigning NamesCounter Specify Counter Specify Counter 0 OK? DVD1 Editing NamesEdit Partition Name OK? Loading Partition?Microboards B.30 Making Copies in Single Master ModeMaster Mode OperationPass 100 Fail Making Copies in Multi Master Mode OK? Input Bin Empty 20 Press OK to Continue Access Log FilePass 16 Fail DVDDuplication Speeds HDD to CD SpeedMicroboards B.30 8. Master Mode HDD to CD Speed Adjusted toMicroboards Copy Erase RW Select Partition Microboards B.30 Copy Hard Drive SetupQuick Erasing Pass 25 FailDelete Partition Load PartitionNew Partition Existing Partition Rename PartitionPartition Info AdminPartition Size Setup Read Error Skip Setup Language Language English Language EspanolFormat Hard Drive Buzzer Setup Max Audio, VCD & CDG Max Audio, VCD & CDG SpeedSetup Setup Startup Menu Startup Menu CopyMicroboards B.30 16. Autocopy Setup Screen Saver Screen Saver On Screen Saver OffSetup Counter Counter On Counter Off Setup Autocopy EnabledLoader Processing Drive 2-Input Bin 11.10 DVD+R High Compatibility ModeSetup 10.DVD+R High Compatibility Loader Processing Please WaitCD 21M Data 1 Session 1Trk Insert Disc menuRAM MB Sdram CPUPlextor Dvdr PX716 Loader Utilities 1. Drive Alignment Please Select Drive Go? System Utilities 4. Load Default Press OK to ContinueLoader Utilities 3. Disc Separator Drive Alignment Alignment Finished?Alignment Next? Drive Alignment Alignment Next?Microboards B.30 14.Manage Accounts Enter PWD OK? Manage Accounts 1. View User AdminLoader Utilities 4. Z form Maneuver Loader Utilities 5.Alignment ProtectionEdit User Info Create UserDelete User Manage Accounts Password on Bootup Password on BootupDrives cannot read disc and shows error message TroubleshootingCode Short Description Full Description Error CodesMicroboards TECHNOLOGY, LLC Menu Tree Actual Size 8-drive Packaged Size 8-drive SpecificationsSupported Formats Technical Support
Top Page Image Contents