MicroBoards Technology HCL-8000, HCL Series, HCL-6000, HCL-4000 user manual Dvd, Pass 16 Fail

Page 18

3. Compare

Use the Compare function to perform a bit-by-bit comparison between the content of your master disc(s) in the Hard Drive and the contents of all discs it copied. This ensures that all of your copies are identical to original master disc(s).

Note: The bit-by-bit comparison will only apply on all DVDs and Data CDs. The readability check will be applied for other formats like Audio CDs, CD+G, and Video CD discs due to their lack of error correction mechanisms.

If you are at the 1. Copy Menu, do the following:

Microboards B.30

1. Copy

(MM)

 

Microboards B.30

3. Compare

 

 

Choose Partition

3-> [DVD1

]DVD

Counter:

No Counter

Use the Up or Down button to find the 3. Compare menu.

Press the OK button on 3. Compare menu to enter the Choose Partition Menu and you will see a screen similar to the following:

Use the Up or Down button to find the partition where your master disc is stored. Press the OK button to select that Partition. Next, you will see

the Counter Selection menu:

Follow the instructions shown in Setting Counters on page 12 to continue. Once the counters have been set, press the OK button to confirm. You will see the Preparing screen.

Preparing...

Please Wait

a screen similar to below:

After a short interval, the robotic loader will pick the top disc from the input spindle and place it into one of the drives. As this is happening, you will see

Loader Processing Drive 1 <- Input Bin

This information screen shows what is happening. In this case, the loader has taken a disc from the input spindle and is placing it into Drive 1.

The loader will continue to remove discs from the input spindle and place those into drives until either all of the drives are full, or the count that you loaded into the counter is reached.

Processing...

Please Wait

It takes a few seconds for the autoloader to recognize all the discs.

The system will then compare the discs in the trays to the content of the master disc residing in the Hard Drive partition you specified. When the comparison job is complete, the autoloader will place the good discs and failed discs into corresponding areas and you will see a PASS/FAIL result screen similar to this:

Counter Specified

PASS 16 FAIL 0

Job Completed! Press OK to Finish

“PASS 16” indicates 16 discs have been compared successfully.

“FAIL 0” indicates none of the discs have failed.

Press the OK button to finish

or:

No Counter Specified

Input Bin Empty (20)

Reset Hoppers?

“Input Bin Empty (20)” indicates that the system has run out of discs to compare.

If you have more discs to compare, you can empty the Output Spindle; place the discs to be compared in the Input Spindle and Press the OK button to continue.

If you have no more discs to compare, press the ESC button to terminate the operation.

18 • Operation

Page 17 Page 19
Image 18
Page 17 Page 19
Contents HCL Series Introduction Table of Contents Introduction Introduction Microboards Statement Regarding Improper Duplication LCD Control Panel Layout Front Panel ControlsMenu Overview CopyAutocopy Enabled Read Error SkipCD Writing Mode DVD+R Compatibility ModeSystem Info Load DefaultUpdate Firmware Device InfoIntroduction to Manage Accounts Single Master ModeMulti Master Mode Batch Mode Single Master and Multi Master ModesSetting Counters and Assigning Names Setting CountersCounter Specify Counter Specify Counter 0 OK? Loading Partition? Editing NamesEdit Partition Name OK? DVD1Operation Making Copies in Single Master ModeMaster Mode Microboards B.30Pass 100 Fail Making Copies in Multi Master Mode Input Bin Empty 20 Press OK to Continue Access Log File OK?DVD Pass 16 FailHDD to CD Speed Duplication SpeedsHDD to CD Speed Adjusted to Microboards B.30 8. Master ModeMicroboards Copy Erase RW Pass 25 Fail Microboards B.30 Copy Hard Drive SetupQuick Erasing Select PartitionRename Partition Load PartitionNew Partition Existing Partition Delete PartitionAdmin Partition InfoPartition Size Setup Language Language English Language Espanol Setup Read Error SkipFormat Hard Drive Setup Startup Menu Startup Menu Copy Setup Max Audio, VCD & CDG Max Audio, VCD & CDG SpeedSetup BuzzerSetup Autocopy Enabled Setup Screen Saver Screen Saver On Screen Saver OffSetup Counter Counter On Counter Off Microboards B.30 16. AutocopyLoader Processing Please Wait 11.10 DVD+R High Compatibility ModeSetup 10.DVD+R High Compatibility Loader Processing Drive 2-Input BinInsert Disc menu CD 21M Data 1 Session 1TrkCPU RAM MB SdramPlextor Dvdr PX716 System Utilities 4. Load Default Press OK to Continue Loader Utilities 1. Drive Alignment Please Select Drive Go?Drive Alignment Alignment Next? Drive Alignment Alignment Finished?Alignment Next? Loader Utilities 3. Disc SeparatorLoader Utilities 5.Alignment Protection Manage Accounts 1. View User AdminLoader Utilities 4. Z form Maneuver Microboards B.30 14.Manage Accounts Enter PWD OK?Create User Edit User InfoDelete User Password on Bootup Manage Accounts Password on BootupTroubleshooting Drives cannot read disc and shows error messageError Codes Code Short Description Full DescriptionMicroboards TECHNOLOGY, LLC Menu Tree Technical Support SpecificationsSupported Formats Actual Size 8-drive Packaged Size 8-drive
Top Page Image Contents