MicroBoards Technology HCL-4000, HCL Series, HCL-6000, HCL-8000 HDD to CD Speed, Duplication Speeds

Page 19
Microboards B.30
1. Copy (MM)
Microboards B.30
6. Select Burn Speed
Select Burn Speed HDD to CD Speed

MICROBOARDS TECHNOLOGY, LLC

HCL Series

4. Test+Copy

With the Test + Copy menu option, the autoloader simulates the copying process, and then makes copies if everything works correctly. If a failure is encountered on a disc during the simulation, it will not be copied during the copying process while the discs that passed the simulation will move on to the copying process. After the copying process, the autoloader will place the failure discs into the reject area while the successfully copied discs will be placed into the corresponding Output Spindle.

Operation in Test+Copy menu is identical to operation in Copy menu.

5. Copy+Compare

The Copy + Compare menu option is used to make verified copies. After the copy process is done, the autoloader automatically compares the copies to the master content residing in the hard drive to ensure that they are identical. When the operation is complete, the autoloader automatically places good discs on to the Output Spindle and bad discs in the Reject Area.

Operation in Copy+Compare menu is identical to operation in Copy menu.

6. Select Burn Speed

The Select Burn Speed menu option is used to adjust the duplication speed for the various duplication modes. By default, the duplication speed will be set to the optimal speed. However, under some circumstances you might want to lower the duplication speed. Those circumstances are:

¾Poor Blank Media Quality - When your media quality is sub-par, lowering the duplication speed is necessary to make good copies.

¾Duplication Quality - Overall, the lower the speed, the higher the quality of your duplicates. If you have time, it is a good choice to lower the speed to produce the best quality duplicates.

If you are at the 1. Copy Menu, do the following:

Use the Up or Down button to find the 6. Select Burn Speed menu.

Press the OK button on 6. Select Burn Speed menu to set the duplication burn speed and you will see the Select Burn Speed type menu similar to below:

There are two recording speed types that can be set:

¾ HDD to CD: Copy Hard Drive CD Content to CD-R/RW Discs speed.

¾HDD to DVD: Copy Hard Drive DVD Content to DVD±R/RW Discs.

Depending upon the type of duplication and your autoloader restrictions, you need to select the correct format in order to take effect. To select the recording speed options, use the Up or Down buttons to find the desired speed for the appropriate format and press the OK button to enter the menu. You will see a menu similar to this:

HDD to CD Speed 32x

Use the Up or Down button to find the desired speed. Press the OK button to set the desired recording speed.

The options that are available are shown in Table 2-1.

Duplication Type

Speeds Available

 

 

 

 

HDD

to

CD

1x, 2x, 4x, 8x, 12x, 16x, 24x, 32x, 40x, 48x,

Speed

 

 

52x

HDD

to

DVD

1x, 2x, 2.4x, 4x, 6x, 8x, 12x, 16x

Speed

 

 

 

 

 

Table 2-1 Duplication Speeds

These options might change depending on the CD or DVD writers pre-installed in your system.

Note: The speed that you choose may be adjusted by the drives and/or the media for optimized duplication.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents HCL Series Introduction Table of Contents Introduction Introduction Microboards Statement Regarding Improper Duplication Front Panel Controls LCD Control Panel LayoutCopy Menu OverviewDVD+R Compatibility Mode Read Error SkipCD Writing Mode Autocopy EnabledDevice Info Load DefaultUpdate Firmware System InfoSingle Master and Multi Master Modes Single Master ModeMulti Master Mode Batch Mode Introduction to Manage AccountsSetting Counters Setting Counters and Assigning NamesCounter Specify Counter Specify Counter 0 OK? DVD1 Editing NamesEdit Partition Name OK? Loading Partition?Microboards B.30 Making Copies in Single Master ModeMaster Mode OperationPass 100 Fail Making Copies in Multi Master Mode OK? Input Bin Empty 20 Press OK to Continue Access Log FilePass 16 Fail DVDDuplication Speeds HDD to CD SpeedMicroboards B.30 8. Master Mode HDD to CD Speed Adjusted toMicroboards Copy Erase RW Select Partition Microboards B.30 Copy Hard Drive SetupQuick Erasing Pass 25 FailDelete Partition Load PartitionNew Partition Existing Partition Rename PartitionPartition Info AdminPartition Size Setup Read Error Skip Setup Language Language English Language EspanolFormat Hard Drive Buzzer Setup Max Audio, VCD & CDG Max Audio, VCD & CDG SpeedSetup Setup Startup Menu Startup Menu CopyMicroboards B.30 16. Autocopy Setup Screen Saver Screen Saver On Screen Saver OffSetup Counter Counter On Counter Off Setup Autocopy EnabledLoader Processing Drive 2-Input Bin 11.10 DVD+R High Compatibility ModeSetup 10.DVD+R High Compatibility Loader Processing Please WaitCD 21M Data 1 Session 1Trk Insert Disc menuRAM MB Sdram CPUPlextor Dvdr PX716 Loader Utilities 1. Drive Alignment Please Select Drive Go? System Utilities 4. Load Default Press OK to ContinueLoader Utilities 3. Disc Separator Drive Alignment Alignment Finished?Alignment Next? Drive Alignment Alignment Next?Microboards B.30 14.Manage Accounts Enter PWD OK? Manage Accounts 1. View User AdminLoader Utilities 4. Z form Maneuver Loader Utilities 5.Alignment ProtectionEdit User Info Create UserDelete User Manage Accounts Password on Bootup Password on BootupDrives cannot read disc and shows error message TroubleshootingCode Short Description Full Description Error CodesMicroboards TECHNOLOGY, LLC Menu Tree Actual Size 8-drive Packaged Size 8-drive SpecificationsSupported Formats Technical Support
Top Page Image Contents