JVC HR-XVC26U manual 14 EN

Page 14

14 EN

INSTALLING YOUR NEW UNIT

Basic Connections

Antenna or Cable

Coaxial cable

Flat feeder

 

 

Matching transformer

 

(not supplied)

AC Outlet

AUDIO

OUTPUT

 

AC Power Cord

VIDEO OUTPUT

Back of unit

VHF/UHF

 

 

IN

Audio/video cable

VHF/UHF OUT

(not supplied)

 

To Audio/video

RF cable

input connectors

(supplied)

To 75 ohm

Terminal

TV

It’s essential that your unit be properly connected.

THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

A Check the contents.

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” on page 87.

B Situate the unit.

Place the unit on a stable, horizontal surface.

C Connect the unit to TV.

The connection method you use depends on the type of TV you have.

RF Connection

8To connect to a TV with NO AV input connectors —

ADisconnect the TV antenna from the TV.

BConnect the TV antenna cable to the VHF/UHF IN connector on the rear panel of the unit.

CConnect the supplied RF cable between the VHF/UHF OUT connector on the rear panel of the unit and the TV’s antenna terminal.

AV Connection

8To connect to a TV with AV input connectors —

AConnect the antenna, unit and TV as per “RF

Connection”.

BConnect an optional audio/video cable between the AUDIO/VIDEO OUTPUT connectors on the rear panel of the unit and the TV’s audio/video input

connectors.

●Set your TV to AV mode.

●For switching the TV’s mode, refer to the instruction manual of your television.

●To obtain high-quality pictures, you can also use the S-VIDEO

connection or Component Video Connection. (DVD deck only) ( pg. 15, 16)

D Connect the unit to power source.

Plug the end of the AC power cord into an AC outlet. This unit performs Plug & Play Set automatically. ( pg. 17)

●The clock and tuner channels will automatically be set when the antenna is connected and when the AC power cord is first connected to an AC outlet. (If “AUTO” and the channel indicator are displayed on the front display panel before the unit is powered on, the clock and tuner channels are being set automatically. Wait for the time to be displayed on the front display panel before turning on the unit.)

E Set the VCR channel.

The VCR channel is the channel on which you can watch the picture from the unit on the TV when only using RF connection.

With RF connection, set the VCR channel to “3 CH” or “4 CH”.

●The VCR channel is preset to “3 CH”. Set to “4 CH” if the Channel 3 is used for broadcasting in your area.

With AV connection, set the VCR channel to “– CH” (off). To set the VCR channel, perform the following steps:

Before performing the following steps:

●Make sure there is no cassette inserted in the unit.

●Make sure the unit is turned on, then press VCR/ DVD on the unit or VCR on the Remote so that the VCR indicator lights up.

APress POWER (1) to turn off the unit, then press STOP (8) on the unit for more than 5 seconds. “3 CH”

appears on the front display panel.

BPress CH +/– on the Remote to select “3 CH”, “4 CH” or “– CH” (off), then press ENTER.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents HR-XVC26U For Customer UseDear Customer Declaration of ConformityPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsTo mobile phone users Do not place the unitDo not block the unit’s ventilation openings or holes On placing the unitFor Servicing Only in U.S.A Warranty Only in U.S.A Unplayable Discs About DiscsPlayable Discs Region NumberMarks related to video DVD Video MarksFile Structure of Discs Audio CD/Video CDOpen the disc tray Placing a DiscCare and Handling of Discs Place the disc10 EN Front ViewRear View To recall an indication 12 ENON-SCREEN Display VCR deck Press on ScreenHow To Use Remote14 EN DVD deck only 8To connect to a TV with S-VIDEO/AUDIO input connectorsConnection Set the VCR channel to off16 EN 8To connect to a TV with component video input connectorsVCR indicator lights up Back of unitPlug & Play Set Perform Plug & Play setupWhat to do if Plug & Play setting failed Auto Clock Set/Auto Tuner SetDVD deck Monitor Set18 EN Pan&Scan Default setting is bold in the table belowPan&Scan/Letter Box Letter BoxLanguage 20 ENOn-screen Language Set DVD deck Press w e to select LanguagePress VCR/DVD repeatedly so that the DVD indicator Can set the default language as you likeOn the DVD Set Up menu screen as an example 22 ENLanguage Code List 24 EN Access the Clock Set screenClock Set PreparationsSemiauto Clock Set Manual Clock Set26 EN Access the Tuner Set screenTuner Set Auto Channel SetAdd or skip the desired channels Access the Manual Channel Set screenManual Channel Set To add channelsBasic Playback 28 ENPause during playback Slow MotionVariable Speed Search Activate frame-by-frame playbackIndex Search 30 ENSkip Search Instant ReViewActivate Repeat Playback Next Function MemoryRepeat Playback Stop Repeat PlaybackSoundtrack Selection Adjust the tracking manuallyManual Tracking Override automatic trackingSet the tape speed Recording Resume FunctionChoose a program Start recordingRecord One Program While Watching Another Instant Timer Recording ITR34 EN Second Audio Recording Reset the counterTape Remaining Time Set the counter displayEnter the program start time Access the Program screen36 EN Enter the program stop timeEnter the channel position Engage the unit’s timer modeTo Timer-Record Weekly Or Daily Serials Cable Box or DBS Receiver UsersPress TIMER, then press Power Disengage the timer modeAccess the Program Check screen Press PROG. CheckReturn to the timer mode To cancel or change a programCancel or change a program Press TimerConfirm the overlapping programs Cancel or change program setting40 EN Select the program to modifyYou can also connect the cable box if it has a timer Satellite Auto RecordingPause playback 42 ENLoad the disc Start playbackAccess the DVD menu Locating a desired scene using the DVD menuAccess the PBC menu Stop modeLocating the start point of the item or skip the item Press Skip 2 or Skip 6 during playbackMemorize the resume point Resume FunctionZooming Resume playback3D Phonic Access the selection menu46 EN Press 3D-PHONICduring playbackVFP function Adjusting the picture quality 48 EN Contents of the on-screen bar during playbackAppears when paused. appears when stopped Press on Screen twice whenever a disc is loadedSelect the option Access the on-screen barChange the time information Select menu item50 EN Select the repeat modeAccess the repeat mode Select the end point To cancel A-B Repeat PlaybackSelect the start point Press rt repeatedly to select A-BSelect the time 52 ENTime Search If you have specified a wrong selectionExamples Chapter SearchSelect the chapter Subtitle Selection Access the menu54 EN Select the subtitle languageSelect the view angle When using the Angle buttonAngle Selection Press AngleAudio Language Selection When using the A.MONITOR button56 EN Select the audio languageFor Video CD Audio Channel SelectionSelect the audio channel For SvcdParental Lock 58 ENTo change the settings To temporarily release the Parental LockCountry/Area Code List for Parental Lock 60 ENPage MP3 control display What is MP3?62 EN Select the group Using the MP3 control displayMP3 Playback Press rt to select the desired group, then press eTo return to the MP3 control display 64 ENGroup/track selection To start playback by specifying the group/track numberWhat is JPEG? Jpeg control display66 EN Using the Jpeg control displayJpeg Playback Slide-show playback starts from the selected filePress Zoom during playback Group/file selectionTo return to the Jpeg control display 68 EN Another Video Recorder Set the input mode of recording deckEngage the Record Pause mode of the recording deck Start the source playerFrom DVD to VCR Dubbing70 EN Prepare the audio device for dubbing Digital Audio DubbingPlace a disc and load a MD For the digital audio device72 EN Make connections 74 EN Mode SetAccess the Function Set screen VCR deckFor Example When this function is set to on 76 ENLanguage Picture Audio Others Back to the beginning For each mode setting, see pages 78 toEach time you press the button, the setup menus Press rt to move the hightlight to RESUME, then press Enter78 EN Picture SettingsAudio Settings Select this when you enjoy conventional 2-channel stereo Select this when you enjoy multichannel surround audio byConnecting the unit’s analogue Audio Output connector Audio by connecting the unit’s analogue Audio OutputChild Lock Scan Mode SetOthers Settings 80 ENOn the unit On the Remote82 EN DVD indicator lights upPress DVD so that the DVD indicator Lights upMP3 Playback DVD deck Recording cannot be started There is no cassette loaded, or84 EN To unlock tray Tray LockTo lock the disc tray 86 EN PlaybackInput/Output RCA connectors X 1, OUT x Signal-to-noise ratio 45 dBHorizontal resolution Signal system88 EN Plug&Play Set Zooming 3D PhonicHOW to Locate Your JVC Service Center 90 ENWarranty Only in U.S.A HR-XVC26U
Top Page Image Contents