JVC HR-XVC26U manual For Example

Page 75

 

 

EN 75

 

 

* The default setting is bold in the table below.

 

 

8 PICTURE CONTROL

This feature helps you to adjust the playback picture quality according to your

NORM

preference. Normally select “NORM”.

EDIT

NORM:

Picture quality is adjusted automatically.

SOFT

EDIT:

Minimizes picture degradation during editing (recording and playback).

SHARP

SOFT:

Reduces image coarseness when viewing overplayed tapes containing a

 

 

 

lot of noise.

 

SHARP

Clearer, sharper-edged picture when viewing images with lots of flat,

 

 

same-coloured surfaces such as cartoons.

 

NOTES:

 

 

● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will not change until you

 

select another mode.

 

● When you select “EDIT” to dub tapes, be sure to select “NORM” after you finish dubbing

 

the tapes.

 

 

 

8 SUPERIMPOSE

When this function is set to “ON”, various operational indicators appear on the TV

ON

screen. Messages appear in the selected language. ( pg. 20)

OFF

NOTES:

 

 

 

 

● When you use this unit as the source player for editing, be sure to set “SUPERIMPOSE” to

 

“OFF” before starting.

 

● During playback, the operation mode indicators may be disturbed depending on the type of

 

tape being used.

 

8AUTO SP]EP TIMER When this function is set to “ON”, the unit automatically switches to EP mode to

ON

allow complete recording if there is not enough tape to record the entire program

OFF

while timer-recording in SP mode.

 

For Example:

 

 

 

Recording a program of 140 minutes in length onto a 120-minute tape

 

Approximately 110 minutes

Approximately 30 minutes

 

 

 

 

 

SP mode

EP mode

 

 

 

 

 

 

Total 140

minutes

 

 

Make sure you set this function to “ON”, before the timer-recording starts.

NOTES:

●If you have programed the unit to timer-record 2 or more programs, the second program and those thereafter may not fit on the tape if you set “AUTO SP]EP TIMER” to “ON”. In this case, make sure the mode is not engaged, then set the tape speed manually during timer programing.

●In order to ensure that the recording fits on the tape, this feature may leave a slight non- recorded section at the end of the tape.

●There may be some noise and sound disturbance at the point on the tape where the unit switches from SP to EP mode.

●The Auto SP]EP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly on the following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120

Page 74 Page 76
Image 75
Page 74 Page 76
Contents For Customer Use HR-XVC26UDeclaration of Conformity Dear CustomerGrounding or Polarization Power SourcesPower Cord Protection Power LinesReplacement Parts AccessoriesCleaning Damage Requiring ServiceOn placing the unit Do not place the unitDo not block the unit’s ventilation openings or holes To mobile phone usersFor Servicing Only in U.S.A Warranty Only in U.S.A Region Number About DiscsPlayable Discs Unplayable DiscsAudio CD/Video CD DVD Video MarksFile Structure of Discs Marks related to videoPlace the disc Placing a DiscCare and Handling of Discs Open the disc trayFront View 10 ENRear View Press on Screen 12 ENON-SCREEN Display VCR deck To recall an indicationRemote How To Use14 EN Set the VCR channel to off 8To connect to a TV with S-VIDEO/AUDIO input connectorsConnection DVD deck onlyBack of unit 8To connect to a TV with component video input connectorsVCR indicator lights up 16 ENAuto Clock Set/Auto Tuner Set Perform Plug & Play setupWhat to do if Plug & Play setting failed Plug & Play SetMonitor Set 18 ENDVD deck Letter Box Default setting is bold in the table belowPan&Scan/Letter Box Pan&Scan20 EN LanguagePress w e to select Language On-screen Language Set DVD deck22 EN Can set the default language as you likeOn the DVD Set Up menu screen as an example Press VCR/DVD repeatedly so that the DVD indicatorLanguage Code List Preparations Access the Clock Set screenClock Set 24 ENManual Clock Set Semiauto Clock SetAuto Channel Set Access the Tuner Set screenTuner Set 26 ENTo add channels Access the Manual Channel Set screenManual Channel Set Add or skip the desired channels28 EN Basic PlaybackActivate frame-by-frame playback Slow MotionVariable Speed Search Pause during playbackInstant ReView 30 ENSkip Search Index SearchStop Repeat Playback Next Function MemoryRepeat Playback Activate Repeat PlaybackOverride automatic tracking Adjust the tracking manuallyManual Tracking Soundtrack SelectionStart recording Recording Resume FunctionChoose a program Set the tape speedInstant Timer Recording ITR 34 ENRecord One Program While Watching Another Set the counter display Reset the counterTape Remaining Time Second Audio RecordingEnter the program stop time Access the Program screen36 EN Enter the program start timeCable Box or DBS Receiver Users Engage the unit’s timer modeTo Timer-Record Weekly Or Daily Serials Enter the channel positionPress PROG. Check Disengage the timer modeAccess the Program Check screen Press TIMER, then press PowerPress Timer To cancel or change a programCancel or change a program Return to the timer modeSelect the program to modify Cancel or change program setting40 EN Confirm the overlapping programsSatellite Auto Recording You can also connect the cable box if it has a timerStart playback 42 ENLoad the disc Pause playbackStop mode Locating a desired scene using the DVD menuAccess the PBC menu Access the DVD menuPress Skip 2 or Skip 6 during playback Locating the start point of the item or skip the itemResume playback Resume FunctionZooming Memorize the resume pointPress 3D-PHONICduring playback Access the selection menu46 EN 3D PhonicVFP function Adjusting the picture quality Press on Screen twice whenever a disc is loaded Contents of the on-screen bar during playbackAppears when paused. appears when stopped 48 ENSelect menu item Access the on-screen barChange the time information Select the optionSelect the repeat mode Access the repeat mode50 EN Press rt repeatedly to select A-B To cancel A-B Repeat PlaybackSelect the start point Select the end pointIf you have specified a wrong selection 52 ENTime Search Select the timeChapter Search Select the chapterExamples Select the subtitle language Access the menu54 EN Subtitle SelectionPress Angle When using the Angle buttonAngle Selection Select the view angleSelect the audio language When using the A.MONITOR button56 EN Audio Language SelectionFor Svcd Audio Channel SelectionSelect the audio channel For Video CD58 EN Parental LockTo temporarily release the Parental Lock To change the settings60 EN Country/Area Code List for Parental LockPage What is MP3? 62 ENMP3 control display Press rt to select the desired group, then press e Using the MP3 control displayMP3 Playback Select the groupTo start playback by specifying the group/track number 64 ENGroup/track selection To return to the MP3 control displayJpeg control display What is JPEG?Slide-show playback starts from the selected file Using the Jpeg control displayJpeg Playback 66 ENGroup/file selection To return to the Jpeg control displayPress Zoom during playback 68 EN Start the source player Set the input mode of recording deckEngage the Record Pause mode of the recording deck Another Video RecorderDubbing 70 ENFrom DVD to VCR For the digital audio device Digital Audio DubbingPlace a disc and load a MD Prepare the audio device for dubbing72 EN Make connections VCR deck Mode SetAccess the Function Set screen 74 ENFor Example 76 EN When this function is set to onPress rt to move the hightlight to RESUME, then press Enter For each mode setting, see pages 78 toEach time you press the button, the setup menus Language Picture Audio Others Back to the beginningPicture Settings Audio Settings78 EN Audio by connecting the unit’s analogue Audio Output Select this when you enjoy multichannel surround audio byConnecting the unit’s analogue Audio Output connector Select this when you enjoy conventional 2-channel stereo80 EN Scan Mode SetOthers Settings Child LockOn the Remote On the unitLights up DVD indicator lights upPress DVD so that the DVD indicator 82 ENRecording cannot be started There is no cassette loaded, or MP3 Playback DVD deck84 EN Tray Lock To lock the disc trayTo unlock tray Playback 86 ENSignal system Signal-to-noise ratio 45 dBHorizontal resolution Input/Output RCA connectors X 1, OUT x88 EN Zooming 3D Phonic Plug&Play Set90 EN HOW to Locate Your JVC Service CenterWarranty Only in U.S.A HR-XVC26U
Top Page Image Contents