JVC HR-XVC26U manual Tray Lock, To lock the disc tray, To unlock tray

Page 85

			EN 85
OTHER PROBLEMS

	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	The image of TV broadcast appears	● The unit leaves turned on and the DVD	Turn off the unit, or press VCR to select the
	distorted on the TV screen.	deck is selected.	VCR deck, then press TV/VCR so that the
			VCR indicator disappears from the front
			display panel.

2.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

3.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them. ( pg. 27)

4.	The channel cannot be changed.	● Recording is in progress.	Press PAUSE (9) to pause the recording,
			change channels, then press PLAY (4) to
			resume recording.

5.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

6.	Even though Auto or Semiauto Clock	● The clock setting data received from the	Select a different host channel during
	Set has been performed, the clock is	host channel is incorrect.	“Semiauto Clock Set” ( pg. 25), or
	incorrect.		perform “Manual Clock Set” ( pg. 25).

ATTENTION

This unit contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the unit off and unplug the AC power cord. Then plug it in again and turn the unit on. Take out the cassette. After checking the cassette, operate the unit as usual.

Tray Lock

You can lock the disc tray to prohibit the unwanted disc ejection by children.

To lock the disc tray.

While the unit is turned off, press and hold 8, then press 1 on the unit. “LOCK” appears on the front display panel.

●If you try to eject the discs, “LOCK” appears and indicates that tray is locked.

To unlock tray

While the unit is turned off, press and hold 1, then press x on the unit. “UNLOCK” appears on the display panel.

Image 85

Contents For Customer Use HR-XVC26UDeclaration of Conformity Dear CustomerPower Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsDo not block the unit’s ventilation openings or holes Do not place the unitTo mobile phone users On placing the unitFor Servicing Only in U.S.A Warranty Only in U.S.A Playable Discs About DiscsUnplayable Discs Region NumberFile Structure of Discs DVD Video MarksMarks related to video Audio CD/Video CDCare and Handling of Discs Placing a DiscOpen the disc tray Place the discFront View 10 ENRear View ON-SCREEN Display VCR deck 12 ENTo recall an indication Press on ScreenRemote How To Use14 EN Connection 8To connect to a TV with S-VIDEO/AUDIO input connectorsDVD deck only Set the VCR channel to offVCR indicator lights up 8To connect to a TV with component video input connectors16 EN Back of unitWhat to do if Plug & Play setting failed Perform Plug & Play setupPlug & Play Set Auto Clock Set/Auto Tuner Set18 EN Monitor SetDVD deck Pan&Scan/Letter Box Default setting is bold in the table belowPan&Scan Letter Box20 EN LanguagePress w e to select Language On-screen Language Set DVD deckOn the DVD Set Up menu screen as an example Can set the default language as you likePress VCR/DVD repeatedly so that the DVD indicator 22 ENLanguage Code List Clock Set Access the Clock Set screen24 EN PreparationsManual Clock Set Semiauto Clock SetTuner Set Access the Tuner Set screen26 EN Auto Channel SetManual Channel Set Access the Manual Channel Set screenAdd or skip the desired channels To add channels28 EN Basic PlaybackVariable Speed Search Slow MotionPause during playback Activate frame-by-frame playbackSkip Search 30 ENIndex Search Instant ReViewRepeat Playback Next Function MemoryActivate Repeat Playback Stop Repeat PlaybackManual Tracking Adjust the tracking manuallySoundtrack Selection Override automatic trackingChoose a program Recording Resume FunctionSet the tape speed Start recording34 EN Instant Timer Recording ITRRecord One Program While Watching Another Tape Remaining Time Reset the counterSecond Audio Recording Set the counter display36 EN Access the Program screenEnter the program start time Enter the program stop timeTo Timer-Record Weekly Or Daily Serials Engage the unit’s timer modeEnter the channel position Cable Box or DBS Receiver UsersAccess the Program Check screen Disengage the timer modePress TIMER, then press Power Press PROG. CheckCancel or change a program To cancel or change a programReturn to the timer mode Press Timer40 EN Cancel or change program settingConfirm the overlapping programs Select the program to modifySatellite Auto Recording You can also connect the cable box if it has a timerLoad the disc 42 ENPause playback Start playbackAccess the PBC menu Locating a desired scene using the DVD menuAccess the DVD menu Stop modePress Skip 2 or Skip 6 during playback Locating the start point of the item or skip the itemZooming Resume FunctionMemorize the resume point Resume playback46 EN Access the selection menu3D Phonic Press 3D-PHONICduring playbackVFP function Adjusting the picture quality Appears when paused. appears when stopped Contents of the on-screen bar during playback48 EN Press on Screen twice whenever a disc is loadedChange the time information Access the on-screen barSelect the option Select menu itemAccess the repeat mode Select the repeat mode50 EN Select the start point To cancel A-B Repeat PlaybackSelect the end point Press rt repeatedly to select A-BTime Search 52 ENSelect the time If you have specified a wrong selectionSelect the chapter Chapter SearchExamples 54 EN Access the menuSubtitle Selection Select the subtitle languageAngle Selection When using the Angle buttonSelect the view angle Press Angle56 EN When using the A.MONITOR buttonAudio Language Selection Select the audio languageSelect the audio channel Audio Channel SelectionFor Video CD For Svcd58 EN Parental LockTo temporarily release the Parental Lock To change the settings60 EN Country/Area Code List for Parental LockPage 62 EN What is MP3?MP3 control display MP3 Playback Using the MP3 control displaySelect the group Press rt to select the desired group, then press eGroup/track selection 64 ENTo return to the MP3 control display To start playback by specifying the group/track numberJpeg control display What is JPEG?Jpeg Playback Using the Jpeg control display66 EN Slide-show playback starts from the selected fileTo return to the Jpeg control display Group/file selectionPress Zoom during playback 68 EN Engage the Record Pause mode of the recording deck Set the input mode of recording deckAnother Video Recorder Start the source player70 EN DubbingFrom DVD to VCR Place a disc and load a MD Digital Audio DubbingPrepare the audio device for dubbing For the digital audio device72 EN Make connections Access the Function Set screen Mode Set74 EN VCR deckFor Example 76 EN When this function is set to onEach time you press the button, the setup menus For each mode setting, see pages 78 toLanguage Picture Audio Others Back to the beginning Press rt to move the hightlight to RESUME, then press EnterAudio Settings Picture Settings78 EN Connecting the unit’s analogue Audio Output connector Select this when you enjoy multichannel surround audio bySelect this when you enjoy conventional 2-channel stereo Audio by connecting the unit’s analogue Audio OutputOthers Settings Scan Mode SetChild Lock 80 ENOn the Remote On the unitPress DVD so that the DVD indicator DVD indicator lights up82 EN Lights upRecording cannot be started There is no cassette loaded, or MP3 Playback DVD deck84 EN To lock the disc tray Tray LockTo unlock tray Playback 86 ENHorizontal resolution Signal-to-noise ratio 45 dBInput/Output RCA connectors X 1, OUT x Signal system88 EN Zooming 3D Phonic Plug&Play Set90 EN HOW to Locate Your JVC Service CenterWarranty Only in U.S.A HR-XVC26U