FUNAI DRV-B2737 Press T-SET, Check the information on the list you will need, If PDC is on

Timer programming list will appear.

DRV_B2737_B2734.book Page 29 Thursday, March 31, 2005 10:04 PM

7 Enter the time to start and to end using [Cursor U / D], then press [Cursor P].

8 Select the channel number to record using [Cursor U / D], then press [Cursor P].

To record from external input, select “AV1,” “AV2” or “AV3.”

9 Select the recording media (“DVD” or “VCR”) using [Cursor U / D], then press [Cursor P].

10 Select the recording speed using [Cursor U / D], then press [Cursor P].

Refer to “Recording speed” on page 22 for DVD or page 63 for VCR.

11 Select PDC “ON” or “OFF” using [Cursor U / D] (See page 30).

12 Press [ENTER] when all information required is entered.

Your programme setting is stored.

•To set another programme, repeat steps 5 to 11.

•To exit, press [SETUP] or [TIMER PROG.].

•If the recording times of two or more programmes overlap, “Overlap” and overlapped programme numbers are displayed. (See page 29 and 31.)

Timer Programming					VCR		DVD
Date Start	End	CH	DVD	Speed		PDC
			VCR
1. 01/01 12:00	13:00	P01	DVD	1H		ON

2. - - -

3. - - -

4. - - -

5. - - -

6. - - -

7

13 Press [T-SET].

The icon will appear on the front panel display and the unit enters to the timer-standby mode.

Note

•If you have not set the clock, the clock setting window will appear after step 4. Continue from step 4 in “Manual Clock Setting” on page 20 before programming the timer.

•Press [Cursor L / P] to move the cursor in the timer programming menu.

•If a basic recording or one-touch timer recording is in progress on one component (e.g. VCR) and the timer recording set for the other component (e.g.

DVD) is about to begin, the unit automatically switches to the programmed channel for timer recording 2 minutes before the programmed starting time, and the recording in progress (for VCR) will be cancelled UNLESS their recording channels are the same. If their recording channels are the same, the timer recording will start without cancelling the recording currently in progress. In this case, the recording of the same channel will be made on both DVD and VCR.

•Cancel the timer-standby mode by pressing [T-SET]before operation for either DVD or VCR. When finished operating, press [T-SET]to resume the timer-standby mode.

If PDC is “ON”:

•In the timer-standby mode, you can neither turn on the power nor use the component (VCR or DVD) which is not currently timer-programmed.

If PDC is “OFF”:

•In the timer-standby mode, you can turn on the power and use the component (VCR or DVD) which is not currently timer-programmed.

Checking, cancelling, or correcting the timer programming information

In the following example, No. 5 timer programming overlaps on No. 1 and No. 6 timer programmes. In such a case, you should correct the programme time to clear the overlap.

	Timer Programming						VCR	DVD
	Date	Start	End	CH	DVD	Speed		PDC
					VCR
1.	01/01 12:00		13:00	AV3 DVD		1H		ON
2.	- - -
3.	- - -		Overlap
4.	- - -		No.1 6
5.	01/01	12:30	14:00	P02	VCR	SP		OFF
6.	01/01	13:45	21:00	P12	DVD	10H		OFF
7.	- - -
8.	- - -

1 Press [T-SET] so that the icon disappears from the front panel display.

2 Press [TIMER PROG.].

3 Check the information on the list you will need.

4 To clear the timer programming, select the desired programme using [Cursor U / D], then press [CLEAR].

To correct the timer programming 1)Select the desired programme using

[Cursor U / D], then press [ENTER]. 2)Correct the timer programming using

[Cursor U / D / L / P].

3)Press [ENTER] again.

29 EN

Recording