Kathrein UFD 515 manual Selecting a radio programme by number entry

Page 24

Programme selection

￿￿button. The radio programme list is now displayed. The upper right-hand column provides information relating to the received satellites, its transmission frequency, the polarisation, the symbol rate, the bouquet and the scrambling. The programme position, the programme name, and type of reception signal (free-to-air/scrambled) are provided on the left. In the upper right-hand field you find the

menu for the menu/ channel setting. Use the ￿￿ buttons to

switch to the next programme, and with ￿￿ buttons to skip to the neighbouring page. The programme selection is confirmed by

pressing ￿.

You can also select the desired programme with the numerical buttons.

Press the ￿ button to exit the programme list and remain in the already set programme.

Selecting a radio programme by number entry

 

You can select a different radio programme during a running radio

 

programme by entering the programme location number. Use the

 

number buttons ￿￿to ￿￿for the purpose of entering the

 

programme location number.

Example

You wish to select the radio programme "DLR-Berlin". This

 

programme is stored under the programme location number 15. (The

 

order of radio programmes is defined in the programme memory, and

 

therefore this only serves as an example.)

 

To select this programme, press the numbers ￿￿and ￿￿one

 

after the other. The receiver waits for about 3 seconds for entry of the

 

next number.

 

Follow the same procedure for all other programmes – i.e. also

 

programmes with three-digit programme location numbers. You do not

 

have to enter leading zeros, unless for accessing teletext.

24

Image 24
Contents Operating manual Page Preface Important notesContents Transponder selection DiSEqC Repeat Safety instructions Place of installation VentilationHumidity, exposure to sunlight, heat Mains voltageControls, displays and connections View of front panelView of rear panel Remote control handset keys Command of remote control Operating instructions Menu conceptButton functions Alphanumeric entries Language selection- OSD Connecting receiver Preconditions for receiving signalsPresetting of receiving system Connection and start-upInserting batteries in the remote control LNB supply voltageTV and video recorder connection Audio connectionFirst time installation Factory setting of receiverFirst steps On screen displays / OSD Important screen displaysHelp function Error message TV channel identifierRadio channel identifier Programme list Radio/TV TeletextProgramme selection Selecting a TV programmeReception status Programme selection Switching to a radio programme Selecting a TV programme by number entryReception status radio Selecting a radio programme by number entry Common Interface Observe the operating manual of your Pay-TV providerCommon Interface Common Interface Timer settings VPS signal Sound settings Setting the volumeStereo and two-channel sound reproduction Switching off sound Programme list Selecting programmes last receivedFavourite programmes Programme list Programme list Programme list Programme list Search programme alphabetically Sorting programmes Deleting programme Be careful when deleting programmes Manually adding programmesProgramme list Setting up a satellite Adding and removing satellitesEntering a satellite name Removing a satelliteProgramme overview EPGEPG timer programming Password Factory settingEntering a password Password Parental lock Password Backup operation Operation from front panelSetting system parameters System parameters System informationLocal time/Timer TV typePicture format ScreenInstallation menu LNB configurationMode Oscillator frequency L.O Standby Antenna settings Antenna rotor / Positioner DiSEqCSatellite search Setting system parameters TP set-up/search Transponder selectionAll new programmes are added to the existing programme list KH signal DiSEqC UFO Set-upTone burst Pre-programming is not deleted with Reset Video recorder connection RecordingPlayback Software and programme list update Software and programme list update „Display info Data transfer from receiver to receiver PreparationTransferring programme lists Transferring operating softwareTechnical features Technical annexTechnical data RF featuresAccessories Switch-over VHS/S-VHSScart socket assignments Connection examples Connection arrangementTechnical annex Short technical lexicon DiSEqCGlossary TransponderService SatelliteDiSEqC menu ZWT Technische Änderungen vorbehalten