Kathrein UFD 515 manual Data transfer from receiver to receiver, Preparation

Page 69

Data transfer from receiver to receiver

Your receiver is able to receive the RS232C socket data from another receiver. To do so, both receivers must be connected via a so-called 'zero modem cable.' The transmitting receiver is in this case the master and the receiving receiver is the slave.

Preparation

The master and slave are first switched to standby mode and then disconnected from the mains by pressing the power switch.

The data sockets of both receivers are connected with the zero modem cable.

The master is then switched on again.

Transferring programme lists

Simultaneously press the ￿￿button (arrow left) and “SELECT” under the front panel of the master to transfer the channel list.

The slave can now be switched on. The transfer procedure begins.

While loading, the display of the master shows "t001 t002 .. t00n“ while the slave correspondingly shows "r001 r002..r00n“.

The LED display shows "----" during block transmission.

The loading procedure was successful, if both receivers show the message "Succ."

Transferring operating software

Follow the same procedure as described above for the purpose of transferring operating software.

Start transfer of the operating software by simultaneously pressing the ￿￿button (arrow right) and “SELECT” under the front panel of the master.

While loading, the display of the master shows "t001 t002 .. t00n“ while the slave correspondingly shows "r001 r002..r00n“.

The LED display shows "----" during block transmission.

The loading procedure was successful, if both receivers show the message "Succ." Should transfer problems occur, "F * * *" will appear in the master display where * stands for a numerical value. In this case, check the cable connection and start a new transfer attempt.

The data transfer from receiver to receiver as described above must only be carried out with devices of the same type as otherwise malfunctions or total loss of the operating software may occur.

On no account must the receivers be switched off or the connection interrupted during data transfer. This may otherwise result in data loss, malfunctions or total failure of the operating system.

Always wait until the "Succ." or "F * * *“ message appears on the display.

69

Image 69
Contents Operating manual Page Important notes PrefaceContents Transponder selection DiSEqC Repeat Safety instructions Ventilation Place of installationHumidity, exposure to sunlight, heat Mains voltageControls, displays and connections View of front panelView of rear panel Remote control handset keys Command of remote control Operating instructions Menu conceptButton functions Alphanumeric entries Language selection- OSD Preconditions for receiving signals Connecting receiverPresetting of receiving system Connection and start-upLNB supply voltage Inserting batteries in the remote controlTV and video recorder connection Audio connectionFirst time installation Factory setting of receiverFirst steps On screen displays / OSD Important screen displaysHelp function Error message TV channel identifierRadio channel identifier Teletext Programme list Radio/TVProgramme selection Selecting a TV programmeReception status Programme selection Switching to a radio programme Selecting a TV programme by number entryReception status radio Selecting a radio programme by number entry Observe the operating manual of your Pay-TV provider Common InterfaceCommon Interface Common Interface Timer settings VPS signal Sound settings Setting the volumeStereo and two-channel sound reproduction Switching off sound Programme list Selecting programmes last receivedFavourite programmes Programme list Programme list Programme list Programme list Search programme alphabetically Sorting programmes Deleting programme Manually adding programmes Be careful when deleting programmesProgramme list Adding and removing satellites Setting up a satelliteRemoving a satellite Entering a satellite nameEPG Programme overviewEPG timer programming Password Factory settingEntering a password Password Parental lock Password Operation from front panel Backup operationSetting system parameters System information System parametersTV type Local time/TimerPicture format ScreenInstallation menu LNB configurationMode Oscillator frequency L.O Standby Antenna rotor / Positioner DiSEqC Antenna settingsSatellite search Setting system parameters Transponder selection TP set-up/searchAll new programmes are added to the existing programme list DiSEqC UFO Set-up KH signalTone burst Pre-programming is not deleted with Reset Video recorder connection RecordingPlayback Software and programme list update Software and programme list update „Display info Preparation Data transfer from receiver to receiverTransferring programme lists Transferring operating softwareTechnical annex Technical featuresRF features Technical dataAccessories Switch-over VHS/S-VHSScart socket assignments Connection arrangement Connection examplesTechnical annex DiSEqC Short technical lexiconTransponder GlossaryService SatelliteDiSEqC menu ZWT Technische Änderungen vorbehalten