Kathrein UFD 430 manual Front panel controls and displays, Remote control handset keys

Page 4
Function 2:
Calls up the menu for radio settings (with ￿press in succession
Stereo/Mono- (2 channel) changeover

Controls, displays and connections

Front panel controls and displays

1Mains switch (with mains isolation)

2LED display for TV (8-position, 7-segment display) Displays programme slot and programme name as well as menu settings.

3Keys for selecting programmes

Step-by-step programme selection (upwards and down- wards).

Switch from standby into operation as well as switchover from TV to radio mode without using remote control.

Remote control handset keys

Function 1:

Command set changeover

Function 2:

To blank out the video signal (in setup mode) This function is to be used if the picture no longer synchro-

￿nises on adjustment and the picture scrolls.

Function 1:

Last-function. Allows you to switch back to the last programme that was selected

Function 2:

￿Displays the info menu

(active only if after pressing the key ￿

the

programme list is displayed.)

 

Function 1:

Calls up TV programme list (or radio programme list in radio mode).

Function 2:

Calls up menu for "Programme slot sorting (insertion), swapping and copying“

"(with ￿press in succession)

Function 1: Volume control Function 2:

To alter settings data in setup mode

￿

Function 1:

Stores the chosen settings Function 2:

Primary key for calling up the separate settings menus (e.g. video settings)

.

Function 1:

Mutes the sound

Function 2:

Calls up the menu for audio settings

(with ￿press in succession)

Rear panel controls and connections

1Mains input socket for 230 V/50 Hz.

2DATA socket

a)Connection facility for the external infrared sensor URS 200.

b)Connection for the UFP 10 Copy-Programmer for read-in and read-out of the programme data.

(function b is especially for service, for copying the programme data).

3VHF/UHF antenna input (signal is looped through).

4VHF/UHF antenna output

(TV signal modulator-output, Ch. 38 is preset).

5Satellite IF, signal input and output of LNB supply voltage.

6Audio output, left and right channel (Cinch sockets).

7Audio digital output (SPDIF output) (Cinch socket)

8Scart socket, TV connection

9Scart socket, VCR connection

10Scart socket, decoder connection

'￿Starts a timer

#Last-function. Allows you to switch back to the last pro- gramme that was selected

)Function 1: On/Off (Standby),

Attention: no mains isolation results!

Function 2:

Return from setup mode into normal operation

,￿Set timer, date and time

Function 1:

Selection of TV/SAT mode Function 2:

Call up the menu for video settings (with ￿press in succession)

Function 1:

Step through the programmes either up or down &Function 2:

Selection of individual menu entries in setup mode

￿Function 1:

Switchover to radio mode

 

Numeric keys 0 - 9 for programme selection and fre-

￿to

quency entries

4

Image 4
Contents Kathrein Satellite Receiver UFD Contents Controls, displays and connections Front panel controls and displays Remote control handset keysRear panel controls and connections Safety instructions Important notes regarding operationImportant notes for siting and installation Connecting up and putting into operation Connecting up the unitSatellite signal connection Receiving system presetsInserting batteries into remote control handset UHF connectionAudio connection Decoder connectionExternal infrared sensor Switching the unit on Adjusting volume, balance and toneReceiver operation Selecting a programmeStereo- / Mono- / Channel changeover Muting the soundSAT/TV changeover Setting date and time Making the settingsSaving settings and starting the clock Return to receive modeTimer setting Making settingsSaving settings Meaning of the columnsDaily and weekly repeated switch-on Video recorder playback VCRAnalogue radio programmes Switching between TV and radio modeDigital radio reception ADR Programme category selection in ADR radio mode Additional functions in ADR mode Search for ADR radio programmesSwitching back to last programme swap Programme sorting inserting, swapping and copyingOperation without remote control Displaying programme overviewStop-watch Info menuTuning in TV programmes Programming TV programmesDescription of menu entries Satellite frequency Video menuPolarisation/Oscillator Video deviation Orbit positionDecoder menu Audio operating mode Programme nameAudio menu Audio carrier frequencySaving the settings Volume offsetAudio de-emphasis for sound type Mono wide only Programming radio programmes Tuning in radio programmesAnalogue radio menu ADR radio menu Calling the initial setup menu Initial settingsModulator output channel OSD language LNB supply voltageLNB supply voltage in standby Programme selectionADR search LED brightnessOscillator frequency DiSEqC menu Changing the oscillator frequencyTone-burst and DiSEqC-signal KHz signalSettings in the DiSEqC menu Tone burst DiSEqCDiSEqC Repeat UFO miniUFO micro EepromSwitching over remote control’s command set Features Specifications Scart connector pin designations ConnectorsTemperature range AccessoriesConnection examples / Service note 935.2076/04.98/SKS/der Subject to alterations