Kathrein MSK 125 manual Channel Display and Entry

Page 46

TV MEASUREMENT

CHANNEL DISPLAY AND ENTRY

To measure the level of a reception signal, you must ﬁrst enter the desired channel.

The following channels can be set:

•	Band I/III	CH 01 to CH 12 in 7 MHz raster
•	Band IV/V	CH 21 to CH 69 in 8 MHz raster
•	Special channel	S 01 to S 20 in 7 MHz raster
•	Special channel	S 21 to S 41 in 8 MHz raster

These details refer to the default Standard B/G only. For information on the other standards please see the technical appendix.

COMMAND OVERVIEW FOR TV CHANNEL ENTRY

	...	Enter channel
		Conﬁrm entry
or	...	Enter channel (automatic
	...	Enter channel (automatic
		conﬁrmation)
	and	Change channels in intervals

Example

To enter channel 28:

Press .

LC display:

•Channel: 28

•Level: 61.0 dBµV

•Operating mode: Analogue terrestrial TV (A = analog)

Note

Ensure that the correct standard has been set. The default setting is Standard B/G.

FREQUENCY DISPLAY AND ENTRY

To measure the level of a reception signal, you must ﬁrst enter the desired video carrier frequency.

The frequency can be entered from 48 MHz to 858 MHz in 50 kHz intervals.

46

Image 46

Contents MSK FOREWORD/IMPORTANT Instructions General Safety InstructionsValidity of this Operating Manual Contents FM Measurement Customer Service Storing Device SettingsMaintenance Features Technical Data Technical AppendixSafety Instructions Safety InstructionsMeaning of Symbols Product PackageFunctionality Function 8PSKTFT Colour Display Operating and Display ElementsLC Display LED DisplayTFT colour display Source selection Measurements LC displayButton Overview of Keypad CommandsInput block Alphanumeric input Operating and Display Elements Front View Fan Ear phones Loudspeakers Battery fuse DC supplyConnections Side ViewUSB Port External DC Power SupplyRF Input Socket SD CardSetup Menu Settings Switch on Switching OFF Setup MenuGetting Started Parameter Setting Mains and Battery OperationDefault Setup Settings AT Time of Shipment Mains OperationBattery Operation SAT SAT ANALOGUE/DVB-S2 SwitchCommand Overview of SAT Frequency Entry Analogue Satellite ReceptionLNB Voltage and 22 KHZ CHANGE-OVER Following voltages can be called up via button commandCommand overview for LNB voltage Button LNB voltageSAT Analogue Level Measurement Sound Carrier Frequency SettingLevel overﬂow and underﬂow Frequency in MHz Bandwidth Select Sound CarrierDigital SAT Reception Called up via button command Following voltages can be ButtonCommand overview for LNB voltage Diseqctm Digital Satellite Equipment Control Setting DVB-S2 Demodulation ParametersSAT DVB-S2 Level Measurement Command Overview for Diseqctm Button Hex codeSAT-CTRL menu DiSEqCTM menu Command Overview for Address Byte Command Overview for Framing ByteHex Byte Description Switch Read switching status ﬂag commited port Command Overview for Command ByteHex Command ID Description ByteCommand Overview for Data Byte Orbit Polarisation Switch Position Data Byte Low BandCommand Overview for Simple Diseqctm List of Single Cable Diseqctm CommandSimple DISEQCTM, Tone Burst Calling up DVB-S2 measurement DVB-S2 MER, BER and Offset MeasurementMpeg Image Representation in DVB-S2 Press to exit digital receptionCommand overview Locating SatellitesCommand overview for ﬁnding Finding Individual Reception FrequenciesTV Measurement Analogue CABLE/DVB C SwitchHF Standard Switch Analogue Cable Demod Menu Analogue TV Cable ReceptionChannel Display and Entry Command Overview for TV Channel EntryFrequency Display and Entry Command Overview for TV Frequency Entry Cable Analogue Level MeasurementLevel Overflow and Underflow Command Overview for Measure TV Audio Carrier FrequencyAudio Carrier Spacing and Level StandardSelect Soundcarrier Digital TV Cable Reception Channel Display and Entry Setting DVB-C Demodulation Parameters DVB-C/DVB-T/H MER, BER and Offset Measurement Level Measurement of DVB-C/DVB-T/H SignalsLC display for DVB-C signals To call up DVB-C/DVB-T/H measurementMpeg Image Representation in DVB-C HF Standard Switch Analogue TERRESTRIAL/DVB T/H SwitchHF Standard Switch Terrestrial Analogue Terrestrial TV ReceptionChannel Display and Entry Command Overview for TV Frequency Entry Select the required HF bandwidth by using the digit buttons Setting DVB-T/H Demodulation ParametersHF Standard Switch DVB-T Digital Terrestrial TV ReceptionChannel Display and Entry DVB-C/DVB-T/H MER, BER and Offset Measurement LC display for DVB-T signals Mpeg Image Representation in DVB-TFinding Individual Reception Frequencies Nicam Audio BIT Error Rate Measurement FM Measurement FM SwitchCommand Overview for FM Frequency Entry Level MeasurementCommand Overview for Find SAT Spectrum Spectrum MeasurementTV Spectrum Spectrum Measurement FM Spectrum Deleting Device Settings Storing Device SettingsStoring Device Settings TFT display LC displaySpectrum Memory Full Only 10 Spec. Possible Storing Measurement ResultsStoring Measurement Results in the Device Memory TFT displayDeleting Measurement Results from the Device Memory Storing Measurement Results on the SD CardStoring Measurement Results Data Logger Entering the Start Line for Automatic MeasuringStarting and Interrupting Automatic Measuring Entering the Stop Line for Automatic MeasuringStoring the Data Logger Measurement Results on the SD Card MessageMaintenance Customer Service Technical Customer SupportFeatures Technical Data RF componentLevel measuring component Technical Appendix SIGNAL-TO-NOISE Ratio+14.1 dB Command SET for EXR 20 Kathrein Matrix Diseqctm Commands for Kathrein MatricesCommand SET for Kathrein Matrices Command SET for EXR 22 Kathrein MatrixChannel Tables Channel UND Frequency TABLE, Standard B/G Frequency in MHZChannel UND Frequency TABLE, Standard L Frequency in MHZ VHF UHFChannel UND Frequency TABLE, D/K Standard Frequency in MHZ VIIChannel UND Frequency TABLE, I Standard Frequency in MHZ Oscillation frequency is made up as follows Calculation of SAT if Frequency Using the MSKThis is done as follows Hence the values for ARD Das Erste arePage Page 936.3474/A/0409/ZWT Technical data subject to change