Strong Enterprises SRT 6850 manual LNB Set-up

Page 30

PART 1 • English

5.1.4.2 LNB Set-up

It is recommended that you read the manual and installation instructions of your LNB, your DiSEqC switch, your 0/12V switch and your Positioner before you start setting up your LNB. To set up your LNB, please apply the following steps:

1.Press the Menu button.

2.Using UP/DOWN keys, select "Installation" and press OK.

3.Using UP/DOWN keys, select "LNB Set-up" and press OK.

4.Check the exact specifications of your LNB through the manufacturers information or your dealer. There are up to 16 types of LNB's available. The Default is set to Universal mode (9750/10600MHz), DiSEqC is not used and the LNB is mounted on a fixed dish.

5.Use the UP/DOWN keys on your remote to select an item and use the LEFT/RIGHT buttons to set up any values.

„LNB: Up to 16 LNBs are available, select and set-up the correct one according to your LNB specifications. Press OK on the LNB number that you want to set-up.

„LNB Type: Select the LNB type from Universal 1 ~ 3, and Single. You should type the LNB value in Single. In Single, the item parameter is 0 or another number. In UNI1=9750/10600 MHz, UNI2=9750/10700 MHz, UNI3=9750/10750 MHz.

„LNB Power: Select 13/18V, 13V or 18V for LNB. Select “Off” if you want to switch the power of the LNB off.

„LNB Dish: Using the Left/Right buttons, select “Fixed” or “Motorised” (Move) Dish. If you use a motorised dish, read the “Positioner Set-up”

„DiSEqC switch: The default is Off. To use the DiSEqC switch, set up the DiSEqC version you have (V1.0 or V1.1).

„DiSEqC Input: Select position 1~4 if DiSEqC switch is DiSEqC V1.0. Select position 1~16 if DiSEqC switch is DiSEqC V1.1.

„DiSEqC Repeat: Designate the repeat of switching (0 ~ 3).

„Switch 22 kHz: You can set the 0/22 kHz switch to ON or OFF.

29

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Page Page Table of Contents Usage Part 1 EnglishDo not Install Your Receiver Features & Accessories AccessoriesSafety Precautions Storage Equipment Set-upYour Receiver SATSAT OUT IR Sensor Connections Connecting to your TV & VCR TV, this will ensure a better Picture and Sound qualityConnection with Audio Cable RCA Connectors At the back of your receiverPlease see inside cover Figure Connecting a remote eye Please see inside cover Figure Connecting a serial cable Please see inside cover FigureConnecting a dish on a motorized positioner to your receiver Quick start Part 1 English Picture below Navigating in the menu Main MenuSee also page 31, 5.1.4.3 Channel Set-up, Scan Mode Channel Organizer MenuImportant Note Channel lists Setting Favourite channels from the channel list Part 1 English Sorting Channels from the channels listEditing Channels from the channel list Change name of channelChange lock function Part 1 English Change the Skip function Deleting Channels from channel listFavourite Organizer Menu Timer Menu Installation Menu System Set-up MenuPart 1 English Press Back until you go back to main menu Part 1 English Part 1 English LNB Set-up Channel Set-up Press the Yellow Save button to save the settings Please also refer to page 18, 5.1.1 Channel Organiser Menu Before you start Parental Lock Changing PIN Code Your Personal PIN Code Smartcard SUB Remote Control Basic functionsStandby ON/OFF TextTV/RAD Pause AudioTrouble Shooting Symptoms CausePart 1 English Symptoms Cause Solution No sound or pictureGlossary of terms Code Subscriber CardTechnical Specifications System & Memory General Data
Top Page Image Contents