Woods Equipment BH6000 manual Swing Cylinder

Page 25

Swing Cylinder

1.

Spanner nut

A.

Seal

2.

Rod guide

B.

O-ring

3.

Barrel

C.

O-ring

4.

Rod assembly

D.

O-ring

5.

Cotter pin

E.

Backup ring

6.

Slotted nut

F.

Rod seal

7.

Piston

G.

Retaining ring

 

 

H.

Wiper

 

 

J.

Iron ring

Figure 20. Swing Cylinder

Disassemble

On the 2-1/2" spanner nut type cylinders, Figure 20, unscrew spanner nut (1) using a spanner wrench, or carefully use a punch and hammer.

Tap rod guide (2) into barrel (3) about 1/2". Remove round retaining ring (G). Pull on rod (4) to remove parts from barrel.

Clamp cross pin end of rod assembly (4) in a vise with protective jaws. Remove cotter pin (5) and nut (6) from rod assembly. Remove piston (7) and rod guide (2) from rod.

Remove and discard all seals, wear rings and O-rings. Clean all components in solvent and blow dry with low pressure air.

Inspect inside of cylinder barrel and rod surface for any scratches or scouring. Small scratches can be removed with fine crocus cloth. If scratches cannot be repaired, replace entire cylinder.

Assemble

Lubricate O-rings and seals with clean hydraulic fluid. Install back-up washer (E) on rod guide (2), then install O-ring (D) in exterior O-ring groove of rod guide. Install rod seal (F) into inner groove of rod guide with open portion of V-groove toward piston.

Place rod wiper (H) in outer rod guide groove. Slide rod guide assembly (5) onto rod (1). Place iron rings (J) in outer grooves of piston. Place piston seal (A) and O- ring (B) in center piston groove. Install O-ring (C) on lip of piston.

Install piston (7) onto rod (4). Install nut (6) and torque to 150-180 lbs-ft. Install cotter pin (5).

Compress iron ring and piston seal and carefully insert piston and rod assembly into barrel. Use care to pre- vent damage while installing.

Carefully push or tap rod guide (2) into barrel (3) just past groove inside barrel. Insert retaining ring (G) into groove and pull rod (4) to seat rod guide (2) against ring. Apply thread-locking compound (removable) to spanner nut (1). Screw spanner nut (1) onto rod guide

(2)using a spanner wrench, or carefully use a punch and hammer.

™

MAN0306 (Rev. 6/16/2006)

Dealer Service 25

 

 

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Backhoe To the Dealer IntroductionTable of Contents English Metric Bucket Description Illustration BH6000 SpecificationsIntroduction Backhoe Components General InformationSafety Rules SafetyInstallation TrainingTransportation OperationStorage MaintenanceLock Safety & Instructional DecalsCrushing Hazard Operation OperationControl Handle Operation Position the MachineFill Bucket Start ExcavationDump and Return Cycle Trenching and ExcavatingThumb Operation Side Slope Trenching or ExcavatingTransport Transport and Swing Lock InstallationTransport Backhoe and Tractor on a Trailer Backhoe Tie Down Location Remove and Store BackhoePRE-OPERATION Check List Owners Responsibility Owner Service Owner ServiceRelief Valve Hydraulic Hoses and FittingsLubrication Points LubricationCleaning TroubleshootingAfter Each Use Periodically or Before Extended StorageDealer Service Dealer ServiceHydraulic Valve Repair Disassemble Spool RepairAssemble Hydraulic Cylinder Repair Adjust Control Valve LinkageGeneral Hydraulic Repair Information Boom, Dipperstick, Bucket & Stabilizer CylindersSwing Cylinder Assembly AssemblyGeneral Assembly Instructions Install StabilizerInstall Bucket Install Dipperstick CylinderInstall Hydraulic Hoses Install Backhoe BracketsStabilizer Pad Point Down Install Optional Stabilizer Street PADDealer Check List Dealer Check ListsPRE-DELIVERY Check List DEALER’S Responsibility Delivery Check List DEALER’S ResponsibilityMAN0306 Rev /23/2008 Parts Parts IndexBH6000 Main Frame Assembly Part QTY Description BH6000 Dipperstick Assembly BH6000 Boom Assembly BH6000 Cylinders BH6000 Valve Controls & HardwareBH6000 Control Valve BH6000 Hoses & Fittings Optional Stabilizer Street PAD BH6000 Hoses & Fittings Parts ListBH6000 Mechanical Thumb SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005 MAN0306
Top Page Image Contents