Woods Equipment BH6000 manual General Assembly Instructions, Install Stabilizer

Page 26

ASSEMBLY

GENERAL ASSEMBLY INSTRUCTIONS

Backhoe assembly is the responsibility of the WOODS dealer. The backhoe should be delivered to the owner completely assembled, lubricated and adjusted for nor- mal operating conditions.

Set backhoe up as received from the factory with these instructions and illustrations.

The backhoe must only be mounted with a Woods sub- frame kit.

When mounting this backhoe on a tractor using a sub- frame mounting, special assembly instructions (which are contained in another manual furnished with the sub-frame) apply to some of the assembly procedures.

The backhoe is shipped partially assembled. Assembly will be easier if components are aligned and loosely assembled before tightening hardware.

Recommended torque values for hardware are given on page 41.

NOTE: References to right, left, forward and rearward directions are determined from the backhoe operator seat position facing rearward.

Figure 18. Backhoe Directions

„Keep all persons away from operator control area while performing adjustments, service, or maintenance.

„Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or other body parts to check for leaks. Wear safety goggles. Hydraulic fluid under pressure can easily penetrate skin and will cause serious injury or death.

„Make sure that all operating and service person- nel know that if hydraulic fluid penetrates skin, it must be surgically removed as soon as possible by

a doctor familiar with this form of injury or gan- grene, serious injury, or death will result. CON-

TACT A PHYSICIAN IMMEDIATELY IF FLUID ENTERS SKIN OR EYES. DO NOT DELAY.

CAUTION

„Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

INSTALL STABILIZER

Remove stabilizer arms from pallet.

Remove pivot pins (3 & 4) from their shipping position. Attach stabilizer arm (1) to main frame (8) using pivot pin (4) and secure with bolt (7) and locknut (6).

Attach stabilizer cylinder (2) to stabilizer arm with pivot pin (3) and secure with cotter pins (5).

1.Stabilizer arm

2.Hydraulic cylinder

3.1.0 x 4.40 Pin

4.6.73 Pin

5.3/16 x 1-1/2 Cotter pin

6.3/8 NC Lock nut

7.3/8 NC x 1 Carriage bolt

8.Main frame

Figure 19. Stabilizer Arm Assembly

26 Assembly

MAN0306 (Rev. 5/23/2008)

 

 

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Backhoe Introduction To the DealerTable of Contents BH6000 Specifications English Metric Bucket Description IllustrationIntroduction General Information Backhoe ComponentsInstallation SafetySafety Rules TrainingOperation TransportationMaintenance StorageSafety & Instructional Decals LockCrushing Hazard Operation OperationPosition the Machine Control Handle OperationDump and Return Cycle Start ExcavationFill Bucket Trenching and ExcavatingSide Slope Trenching or Excavating Thumb OperationTransport Backhoe and Tractor on a Trailer Transport and Swing Lock InstallationTransport Remove and Store Backhoe Backhoe Tie Down LocationPRE-OPERATION Check List Owners Responsibility Relief Valve Owner ServiceOwner Service Hydraulic Hoses and FittingsLubrication Lubrication PointsAfter Each Use TroubleshootingCleaning Periodically or Before Extended StorageHydraulic Valve Repair Dealer ServiceDealer Service Assemble Spool RepairDisassemble General Hydraulic Repair Information Adjust Control Valve LinkageHydraulic Cylinder Repair Boom, Dipperstick, Bucket & Stabilizer CylindersSwing Cylinder General Assembly Instructions AssemblyAssembly Install StabilizerInstall Hydraulic Hoses Install Dipperstick CylinderInstall Bucket Install Backhoe BracketsInstall Optional Stabilizer Street PAD Stabilizer Pad Point DownPRE-DELIVERY Check List DEALER’S Responsibility Dealer Check ListsDealer Check List Delivery Check List DEALER’S ResponsibilityMAN0306 Rev /23/2008 Parts Index PartsBH6000 Main Frame Assembly Part QTY Description BH6000 Dipperstick Assembly BH6000 Boom Assembly BH6000 Valve Controls & Hardware BH6000 CylindersBH6000 Control Valve BH6000 Hoses & Fittings BH6000 Hoses & Fittings Parts List Optional Stabilizer Street PADBH6000 Mechanical Thumb Appendix Bolt Torque ChartSAE Series Torque Chart Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005 MAN0306
Top Page Image Contents