Woods Equipment BH6000 manual Remove and Store Backhoe, Backhoe Tie Down Location

Page 17

Figure 12. Backhoe Tie Down Location

REMOVE AND STORE BACKHOE

„The only time the backhoe may be operated from a position other than the operator seat is dur- ing backhoe attachment and removal. Operator must:

Read Mounting Kit Manual instructions on attaching and removing backhoe and use extreme care.

Always stand between rear tire and backhoe stabilizer arms or along side of tractor to avoid being trapped should the boom swing control be accidentally activated.

„Keep all persons away from operator control area while performing adjustments, service, or maintenance.

NOTE: See the sub-frame mounting kit manual that fits your tractor for specific instructions.

1.Position tractor on a hard level surface and center the backhoe boom.

2.Lower stabilizers and take weight off of rear tractor tires.

3.Lower boom and dipper to form 90-degree angle and rest bucket on the ground.

4.Remove klik pins from lock pins. Remove lock pins and rotate latches into the open position. Install lock pins to secure.

5.Lower stabilizers until backhoe mounts clear the tractor brackets.

6.Lower backhoe until backhoe mounts are firmly on the ground. Raise stabilizers all the way up. Retract boom cylinder and engage lock bar.

7.Turn off engine, set brakes, and remove key.

8.Disconnect backhoe hydraulic hoses from tractor.

NOTICE

Failure to connect tractor hoses together will result in damage to tractor hydraulic system.

9.Connect male quick coupler on the end of the RETURN hose to the female quick coupler on the bulkhead support bracket when backhoe is removed (Figure 13).

Figure 13. Hose Connection - Backhoe Removed

10.Connect IN and OUT quick couplers on backhoe together to prevent dirt and debris from accumulat- ing in quick couplers.

Figure 14. Backhoe Hose Connection

MAN0306 (Rev. 5/23/2008)

Operation 17

 

 

Image 17
Contents Backhoe To the Dealer IntroductionTable of Contents English Metric Bucket Description Illustration BH6000 SpecificationsIntroduction Backhoe Components General InformationSafety Rules SafetyInstallation TrainingTransportation OperationStorage MaintenanceLock Safety & Instructional DecalsCrushing Hazard Operation OperationControl Handle Operation Position the MachineFill Bucket Start ExcavationDump and Return Cycle Trenching and ExcavatingThumb Operation Side Slope Trenching or ExcavatingTransport Backhoe and Tractor on a Trailer Transport and Swing Lock InstallationTransport Backhoe Tie Down Location Remove and Store BackhoePRE-OPERATION Check List Owners Responsibility Owner Service Owner ServiceRelief Valve Hydraulic Hoses and FittingsLubrication Points LubricationCleaning TroubleshootingAfter Each Use Periodically or Before Extended StorageHydraulic Valve Repair Dealer ServiceDealer Service Assemble Spool RepairDisassemble Hydraulic Cylinder Repair Adjust Control Valve LinkageGeneral Hydraulic Repair Information Boom, Dipperstick, Bucket & Stabilizer CylindersSwing Cylinder Assembly AssemblyGeneral Assembly Instructions Install StabilizerInstall Bucket Install Dipperstick CylinderInstall Hydraulic Hoses Install Backhoe BracketsStabilizer Pad Point Down Install Optional Stabilizer Street PADDealer Check List Dealer Check ListsPRE-DELIVERY Check List DEALER’S Responsibility Delivery Check List DEALER’S ResponsibilityMAN0306 Rev /23/2008 Parts Parts IndexBH6000 Main Frame Assembly Part QTY Description BH6000 Dipperstick Assembly BH6000 Boom Assembly BH6000 Cylinders BH6000 Valve Controls & HardwareBH6000 Control Valve BH6000 Hoses & Fittings Optional Stabilizer Street PAD BH6000 Hoses & Fittings Parts ListBH6000 Mechanical Thumb SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005 MAN0306