Extron electronic AVT 200HD manual Installation Overview

Page 10

Installation

This section describes the rear panel of the AVT 200HD and provides instructions for cabling. It covers the following topics:

•Installation Overview

•Rear Panel Features

•Control Connections

Installation Overview

Follow these steps to install and set up the AVT 200HD tuner:

1.Disconnect power from the tuner and turn off all other devices that are connected to it.

2.(Optional) Mount the unit in a rack. Rack mount the tuner using the supplied brackets (see the “Mounting the Tuner” in the “Reference Information” section).

3.Connect the RF input. Connect an antenna or a CATV cable to the RF In F-type connector (J on the rear panel diagram on the next page).

4.Connect the video output. Connect a television or other output device to one of the following video output connectors:

•VID — Composite video (B, top, on the rear panel diagram)

•YC — S-video (B, bottom, on the rear panel diagram)

•RGBHV — RGBHV (C on the rear panel diagram)

•Component video — YUVp/HD or YUVi (D on the rear panel diagram)

•HDMI — HDMI digital (E on the rear panel diagram)

5.Connect the audio output. Connect a speaker set, amplifier, receiver, or other audio output device to one or more of the following connectors:

•RCA — Unbalanced analog (F on the rear panel diagram)

•Captive screw — Balanced or unbalanced analog (G on the rear panel diagram)

•Coax — Digital S/PDIF (H on the rear panel diagram)

•Optical — (Fiber optic) Digital S/PDIF (I on the rear panel diagram)

6.Connect control devices: Connect your computer to one of these AVT ports to configure and control the tuner via the Windows®-based software or SIS commands.

•RS232 port — Serial RS-232 control (K on the rear panel diagram)

•LAN Ethernet port — Ethernet control via Internet browser (L on the rear panel diagram)

•Config port — USB connection (B on the front panel diagram in the “Operation” section)

7.Connect power to the AVT by connecting a standard IEC power cord (provided) from

a 100 to 240 VAC, 50-60 Hz power source to the AC power receptacle (A on the rear panel diagram).

AVT 200HD Tuner • Installation

4

Image 10

Contents AVT 200HD Safety Instructions English FCC Class a Notice Conventions Used in this Guide Contents Html Configuration About this Guide FeaturesAbout the AVT 200HD Tuner AVT 200HD Tuner Introduction Application Diagram Application Diagram for the AVT 200HDInstallation Installation OverviewVideo Output Connectors Rear Panel FeaturesComposite and S-video stacked video output connectors Audio Output Connectors Analog audio output connectorsRemote Configuration and Control Connectors Input ConnectorDigital audio output connectors Control Connections Wiring for RS-232 ControlEthernet Connection Wiring for IR Control Wiring the IR LinkConnecting to the USB Port Connecting the AVT 200HD to the IR LinkFound New Hardware Wizard Opening Screen AVT 200HD Tuner Installation Front Panel Features AVT 200HD Front PanelHdcp Compliance NBC-4LAPowering On Power-up and Default Cycle Screens ExampleMenus on the LCD Screen Using the menusMenu System Overview Menu flow diagram AVT 200HD Menu FlowScanning for channels Channel Setup MenuSelecting the signal source Option Scans forScanning Channels with long minor numbers CableOutput Configuration Menu Selecting tune or preset modeSaving presets Not available via the front panel Selecting a channelRecalling presets Selecting the output resolution and refresh rateSelecting the display aspect ratio Selecting the display modeResolution Composite Simultaneous Video OutputAudio Configuration Menu Selecting the closed caption serviceComm Setting Menus Comm Setting Menu FlowViewing serial port and IP settings Configuring the serial port and IP parametersUnit Reset Menu Resetting from the Front Panel Unit Reset Menu FlowResetting from the Rear Panel Volume ControlExiting the Menu System Reset Modes Summary Activation Result Purpose/Notes Exec Mode Select Disable Locking and Unlocking the Front Panel Executive ModesUsing the AVT 200HD IR Remote Control Executive Mode Menu FlowInstalling batteries in the AVT 100 Remote Area for Remote Signal ReceptionButtons on the AVT 200HD Remote Control Buttons on the AVT 200 Remote ControlSelecting a Channel or Preset Using the IR Remote Control Channel Selection buttons 0 throughLocking IR Remote Control Access Using the On-screen Display OSDIntroductory Display Volume Level Display Channel Information DisplayProgram Guide Ethernet Port Serial PortUSB Port Ethernet CableIP Address Connection TimeoutsEstablishing an Ethernet Connection Chip Security for Parental Control Using SIS CommandsTuner-initiated Messages Copyright message With an RS-232 connectionError Response References Tuner Error ResponsesUsing the Command/Response Tables for SIS Commands X1@ Symbol Definitions for AVT 200HD Specific CommandsSpecial Characters X1#X2@ X2# X2% X3@ X3#Command/Response Table for AVT 200HD SIS Commands EX!*X@TVSLX!*X@TVCH EX!*X@TVCHX2%TVPR EX2RATE EX2%NGEX2&OPOL EX1TVOS EX1TVTMEX1TVPG X1% X1 TvccX1% Fscc X1 FsccX2*FSCC X1&FSCCX1*FSCC ExafmtX1$ VolX1$ Chip Setup Parental ControlEX* Lang X3@X3@*X2@VCHP Chip SetupX3@*X1VCHP X2@$ Tvst Other SettingsTvst ‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘ Executive Mode Front Panel Lockout Information RequestsResets EZIX4# Symbol Definitions for IP-specific CommandsX5# X5$ X7# X6#X6$ X7$X8# X8$EX4!CP Command/Response Table for IP-Specific SIS CommandsEX!CE EX5#CT EX5@CNECN ECTECI EDHEX5$CI ECHEX7$ ,X5$ ID EdiX7$ *X5$ *X4@ BmdX9% ,X5$EX4@ *X10# *X10$ PB BptX4@ *X5 X7$ = 0EX4@MD EX4@MHEMH EMDEX7$ ,X7% ,X7 ,X7& E EX7$ ,X7% ,X7 ,X7*X7& E EvtX7$ ,X7% ,X7 ,X7EvtX7$,X7%,X7, string EX7$ ,X7% ,X7 ,X8 FEDownloading and Installing the Software from the Web Accessing the AVT 200HD Configuration & Control SoftwareComputer System Requirements Installing the Software from the Disc Software Button on the DVD Opening ScreenCommunication Setup Window with Telnet Tab Starting the SoftwareRS232 Connection Tab Setup Tab on the Main Window Using the Configuration & Control Program Help File Updating the FirmwareExtron Firmware Loader Window for AVT 200HD Firmware Update in Progress Accessing the Web Pages HtmlExample of a Network Password Dialog Box Special CharactersSystem Status System StatusConfiguration Pages System SettingsIP Settings Fields Unit Name fieldDate/Time Settings Fields Date/Time Settings FieldsTuner Settings Tuner SettingsTo hide a channel Edit Channels and Presets sectionChannel Scan section To show a hidden channelOutput Setup section Executive ModeSetting a password PasswordsRemoving passwords Firmware Upgrade Firmware UpgradeChoose File Window with a Firmware File Selected File Management Uploading FilesAdding a Directory Other File Management ActivitiesControl Pages User ControlAdjusting the volume Selecting a presetKeypad Closed Captioning Closed CaptioningChip Text Size Text Style Text Fill Text ColorMovie Rating Parental Control section Chip ScreenTV Rating Parental Control section Maximum Allowed TV Rating for Ages sectionChange PIN section RF video input SpecificationsSignal processing Video output analogAudio output analog Video output digitalSync Audio output digitalPower VAC to 240 VAC, 50-60 Hz, 25 watts, internal GeneralIncluded Parts Part Numbers and AccessoriesOptional Accessories CablesMounting the Tuner Rack Mounting ProcedureUL Guidelines for Rack Mounting Choosing IP Addresses What is an IP Address?IP Addressing Class Name Valid Address Range Identifier ArrangementPinging to determine the Extron IP address Subnet MaskPinging for the IP Address Class Name Subnet MaskConnecting as a Telnet Client Pinging to determine the web IP addressConnecting to the AVT Open command Telnet tipsLocal and remote devices Subnetting a PrimerGateways IP addresses and octetsUnmasked octets are compared indicated by ? in figure Subnet masks and octetsDetermining whether devices are on the same subnet Masked octets are not compared indicated by X in figurePhysical Lower Edge Video Frequency TablesAtsc Frequency Table Audio Upper Edge ChannelAtsc Frequency Table Cable Frequency Table HRC CablePhysical Channel Visual Carrier Frequency MHz Cable Frequency Table Cable Frequency Table Asia Middle East USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Europe