Extron electronic AVT 200HD manual Hdcp Compliance, NBC-4LA

Page 20

EUp (>) and Down (<) buttons — These buttons change the channel or preset, depending on the selected operating mode. Each press increments or decrements the number in the LED display (C).

•In Tune mode (default): The buttons select channel numbers to switch channels that have saved in the channel list (either manually or by Auto-Scan; see “Scanning for Channels,” later in this section).

•In Preset mode: The buttons select the preset numbers to switch channels that have been saved as presets.

Pressing and holding a button causes the displayed numbers to cycle up or down rapidly. When you release the button, the channel or preset number that appears in the LED display is selected.

FLCD window — This window displays messages, menu information, and your menu selections (see “Menus on the LCD Screen,” later in this section, for information on using the AVT menu system).

GMenu button — Press this button to access the AVT 200HD menu system and step through the menus.

HNext button — Within a menu, press this button to step through the submenus.

IAdjustment knobs — Within a submenu, turn these horizontal and vertical

Adjustment knobs to select options from the submenu, such as the output resolution or the RF source (Air or Cable).

JVolume knob — Turn this knob to adjust the output volume between 0% (muted) and 100%.

NOTE: This knob adjusts volume for analog and PCM digital output only. It does not affect Dolby digital (AC-3) volume.

HDCP Compliance

When a broadcast flag, indicating protected material, is detected in the television data stream, the LCD screen on the front panel displays an asterisk (*) in the lower-right corner (see the example below).

NBC–4LA

AIR 4–1 *

The AVT 200HD immediately disables any analog video and audio outputs.

For an HDMI connection, the AVT checks the EDID of the connected display and outputs

HDMI video or audio only if the monitor is HDCP-compliant.

Analog video and audio resume when the broadcast flag is removed.

NOTE: If you not in a position to view the front panel LCD screen, you can check

whether the broadcast flag is on or off by entering the SIS command

E I HDCP}. The system responds with 0 if the broadcast flag is off or 1 if it is

on.

See the View broadcast flag command in the “Remote Configuration and Control” section for more information.

AVT 200HD Tuner • Operation

14

Page 19 Page 21
Image 20
Page 19 Page 21
Contents AVT 200HD Safety Instructions English FCC Class a Notice Conventions Used in this Guide Contents Html Configuration About the AVT 200HD Tuner FeaturesAbout this Guide AVT 200HD Tuner Introduction Application Diagram Application Diagram for the AVT 200HDInstallation Installation OverviewComposite and S-video stacked video output connectors Rear Panel FeaturesVideo Output Connectors Audio Output Connectors Analog audio output connectorsDigital audio output connectors Input ConnectorRemote Configuration and Control Connectors Ethernet Connection Wiring for RS-232 ControlControl Connections Wiring for IR Control Wiring the IR LinkConnecting to the USB Port Connecting the AVT 200HD to the IR LinkFound New Hardware Wizard Opening Screen AVT 200HD Tuner Installation Front Panel Features AVT 200HD Front PanelHdcp Compliance NBC-4LAPowering On Power-up and Default Cycle Screens ExampleMenu System Overview Using the menusMenus on the LCD Screen Menu flow diagram AVT 200HD Menu FlowChannel Setup Menu Selecting the signal sourceScanning for channels Option Scans forScanning Channels with long minor numbers CableOutput Configuration Menu Selecting tune or preset modeSaving presets Not available via the front panel Selecting a channelRecalling presets Selecting the output resolution and refresh rateSelecting the display mode Resolution CompositeSelecting the display aspect ratio Simultaneous Video OutputAudio Configuration Menu Selecting the closed caption serviceComm Setting Menus Comm Setting Menu FlowViewing serial port and IP settings Configuring the serial port and IP parametersUnit Reset Menu Resetting from the Front Panel Unit Reset Menu FlowExiting the Menu System Volume ControlResetting from the Rear Panel Reset Modes Summary Activation Result Purpose/Notes Exec Mode Select Disable Locking and Unlocking the Front Panel Executive ModesUsing the AVT 200HD IR Remote Control Executive Mode Menu FlowInstalling batteries in the AVT 100 Remote Area for Remote Signal ReceptionButtons on the AVT 200HD Remote Control Buttons on the AVT 200 Remote ControlSelecting a Channel or Preset Using the IR Remote Control Channel Selection buttons 0 throughIntroductory Display Using the On-screen Display OSDLocking IR Remote Control Access Volume Level Display Channel Information DisplayProgram Guide Serial Port USB PortEthernet Port Ethernet CableEstablishing an Ethernet Connection Connection TimeoutsIP Address Using SIS Commands Tuner-initiated MessagesChip Security for Parental Control Copyright message With an RS-232 connectionUsing the Command/Response Tables for SIS Commands Tuner Error ResponsesError Response References Symbol Definitions for AVT 200HD Specific Commands Special CharactersX1@ X1#X2@ X2# X2% X3@ X3#Command/Response Table for AVT 200HD SIS Commands EX!*X@TVSLX2%TVPR EX!*X@TVCHX!*X@TVCH EX2&OPOL EX2%NGEX2RATE EX1TVPG EX1TVTMEX1TVOS X1 Tvcc X1% FsccX1% X1 FsccX1&FSCC X1*FSCCX2*FSCC ExafmtChip Setup Parental Control EX* LangX1$ VolX1$ X3@Chip Setup X3@*X1VCHPX3@*X2@VCHP X2@Tvst ‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘‘ Other Settings$ Tvst Executive Mode Front Panel Lockout Information RequestsResets EZIX5# X5$ Symbol Definitions for IP-specific CommandsX4# X6# X6$X7# X7$X8# X8$EX!CE Command/Response Table for IP-Specific SIS CommandsEX4!CP EX5@CN ECNEX5#CT ECTEDH EX5$CIECI ECHBmdX9% ,X5$ EX4@ *X10# *X10$ PB BptX4@ *X5EX7$ ,X5$ ID EdiX7$ *X5$ *X4@ X7$ = 0EX4@MH EMHEX4@MD EMDEX7$ ,X7% ,X7 ,X7& E EX7$ ,X7% ,X7 ,X7*X7& E EvtX7$ ,X7% ,X7 ,X7EvtX7$,X7%,X7, string EX7$ ,X7% ,X7 ,X8 FEComputer System Requirements Accessing the AVT 200HD Configuration & Control SoftwareDownloading and Installing the Software from the Web Installing the Software from the Disc Software Button on the DVD Opening ScreenCommunication Setup Window with Telnet Tab Starting the SoftwareRS232 Connection Tab Setup Tab on the Main Window Using the Configuration & Control Program Help File Updating the FirmwareExtron Firmware Loader Window for AVT 200HD Firmware Update in Progress Accessing the Web Pages HtmlExample of a Network Password Dialog Box Special CharactersSystem Status System StatusConfiguration Pages System SettingsIP Settings Fields Unit Name fieldDate/Time Settings Fields Date/Time Settings FieldsTuner Settings Tuner SettingsEdit Channels and Presets section Channel Scan sectionTo hide a channel To show a hidden channelOutput Setup section Executive ModeRemoving passwords PasswordsSetting a password Firmware Upgrade Firmware UpgradeChoose File Window with a Firmware File Selected File Management Uploading FilesAdding a Directory Other File Management ActivitiesControl Pages User ControlKeypad Selecting a presetAdjusting the volume Closed Captioning Closed CaptioningChip Text Size Text Style Text Fill Text ColorMovie Rating Parental Control section Chip ScreenTV Rating Parental Control section Maximum Allowed TV Rating for Ages sectionChange PIN section Specifications Signal processingRF video input Video output analogVideo output digital SyncAudio output analog Audio output digitalPower VAC to 240 VAC, 50-60 Hz, 25 watts, internal GeneralPart Numbers and Accessories Optional AccessoriesIncluded Parts CablesUL Guidelines for Rack Mounting Rack Mounting ProcedureMounting the Tuner What is an IP Address? IP AddressingChoosing IP Addresses Class Name Valid Address Range Identifier ArrangementSubnet Mask Pinging for the IP AddressPinging to determine the Extron IP address Class Name Subnet MaskConnecting as a Telnet Client Pinging to determine the web IP addressConnecting to the AVT Open command Telnet tipsSubnetting a Primer GatewaysLocal and remote devices IP addresses and octetsSubnet masks and octets Determining whether devices are on the same subnetUnmasked octets are compared indicated by ? in figure Masked octets are not compared indicated by X in figureFrequency Tables Atsc Frequency TablePhysical Lower Edge Video Audio Upper Edge ChannelAtsc Frequency Table Cable Frequency Table HRC CablePhysical Channel Visual Carrier Frequency MHz Cable Frequency Table Cable Frequency Table USA, Canada, South America Japan Central America Europe, Africa, and the Middle China EastAsia Middle East Europe
Top Page Image Contents