SUPER MICRO Computer 5017P-TF, 5017P-TLN4F user manual Installing the Chassis into a Telco Rack

Page 19

Chapter 2: Server Installation

Telco Rack

The SC504 supports Telco Rack installation. The SC504 chassis' compact design allows the it to be installed into a Telco rack without the use of rails.

Figure 2-2. Installing the Chassis into a Telco Rack

Installing the Chassis into a Telco Rack

1.To install the chassis into a Telco style two-post rack, use two L-shaped brackets on either side of the chassis (four total).

2.First, determine how far follow the server will extend out the front of the rack. Larger chassis should be positioned to balance the weight between front and back.

3.If a bezel is included on your chassis, remove it. Then attach the two front brackets to each side of the chassis, then the two rear brackets positioned with just enough space to accommodate the width of the Telco rack.

4.Finish by sliding the chassis into the rack and tightening the brackets to the rack.

Note: the figures are for illustrative purposes only. Always install chassis starting from the bottom of the rack and working up.

2-5

Image 19

Contents Super Manual Revision Release Date July 19 Manual Organization About This ManualAdvanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents System Safety Bios Overview Chapter IntroductionPCI Expansion Slots Motherboard FeaturesProcessors Memory Serial ATAFront Control Panel Server Chassis FeaturesSystem Power Hard Drive SubsystemIntel QM77 Chipset System Block Diagram Asia-Pacific Contacting SupermicroHeadquarters EuropePage Choosing a Setup Location Preparing for SetupUnpacking the System Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureInstalling the Chassis into a Standard Rack Installing the System into a RackTelco Rack Installing the Chassis into a Telco RackPage Power ResetControl Panel Buttons Description Power FailControl Panel LEDs Informational LED StatusHDD Drive Carrier LEDsPage Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsChapter Advanced Motherboard Setup Connecting the Control Panel Connecting CablesConnecting Data Cables Connecting Power CablesRear I/O Ports Control Panel Header PinsAdding PCI Add-On Cards Installing MemoryHow to Install SO DIMMs Onboard Processor and HeatsinkTo Remove SO Dimm SocketX9SPV-LN4F/F-3610ME Layout Motherboard DetailsJumper Description Default Setting Connector DescriptionX9SPV-LN4F/F-3610ME Quick Reference Reset Button Connector DefinitionsPower Connectors Power ButtonNMI Button Power On LEDSerial Ports Ethernet PortsFan Headers Chassis IntrusionUniversal Serial Bus USB Internal SpeakerLAN Ports LAN1~LAN4 Sgpio Headers Power LED/SpeakerOverheat/Fan Fail LED Power Supply SMBus I2C Header DOM Power ConnectorCmos Clear Jumper SettingsBios Write Protect JWP1 Explanation of JumpersBMC Enable/Disable Watch Dog Enable/DisableUSB Wake-Up JPUSB1 Ipmi Heartbeat LED LED2 Onboard IndicatorsStandby Power LED LED1 LAN LEDsSerial ATA Ports Sata and SAS PortsDriver/Tool Installation Display Screen Installing SoftwareSuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Front and Rear Chassis Views Control PanelRemoving the Chassis Cover Removing the Chassis CoverSystem Fans Optional Installing Hard DrivesInstalling 2.5 Hard Drives Installing Hard Drives Hard Drive Configuration OptionsLocating the Expansion Card Clip Installing an Expansion CardInstalling the Expansion Card Replacing the Power Supply Power SupplyPage How To Change the Configuration Data Starting Bios Setup UtilityIntroduction How to Start the Setup Utility Main SetupSystem Memory System Time/System DateSupermicro X9SPV-F/LN4F ProcessorBootup Num-Lock Advanced Setup ConfigurationsBOOT Feature Quiet BootProcessor and Clock Options Clock Spread Spectrum Hardware Prefetcher Available when supported by the CPUActive Processor Cores Limit Cpuid MaximumLong Duration Power Limit CPU PPM Configuration Power TechnologyTurbo Mode Config TDP LockAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration USB Ports Per-Port Disable Control Xhci Pre-Boot DriverXhci Mode HS Port #1~#4 SwitchableIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings Target Link Speed Available when supported by the hardware IDO Request Enable Available when supported by the hardwareOnboard LAN Option ROM Select Compliance SOS Available when supported by the hardwareIs Disabled Network Stack PCI-E Slot 1 Option ROMAuto Super IO Device ConfigurationSerial Port 1 Settings / Serial Port 2 Settings Ipv6 PXE SupportConsole Redirection Settings Remote Access ConfigurationRedirection After Bios Post Recorder ModeResolution Legacy OS Redirection ResolutionOut-of-Band-Mgmt Port Console Redirection Settings for EMSACPI Configuration High Precision TimerIntel Txtlt Configuration Trusted Computing ConfigurationISCSI Configuration Delete Attempts Add an AttemptChange Attempt Order Wake On LAN Port Configuration InformationEvent Logs Link SpeedChange SmBIOS Event Log Settings When SEL Full Ipmi SettingsSystem Event Log Log EFI Status Codes BMC Network ConfigurationUpdate Ipmi LAN Configuration Configuration SourceBoot HDD Password Security SettingsAdministrator Password User PasswordDiscard Changes Save Changes and ResetExit Discard Changes and ExitBoot Override Restore DefaultsSave As User Defaults Restore User DefaultsRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front