SUPER MICRO Computer 5017P-TLN4F, 5017P-TF user manual Removing the Chassis Cover

Page 52

Chapter 6: Advanced Chassis Setup

6-3 Removing the Chassis Cover

13

12

12

12

Figure 6-2. Removing the Chassis Cover

Removing the Chassis Cover

1.Power down the system and disconnect the power cord from the back of the power supply.

2.Remove the five screws that hold the chassis cover in place. There are two screws on each side of the chassis, and one screw on the back.

3.Once the screws have been removed, lift the cover upward to remove it from the chassis.

Caution: Except for short periods of time, do NOT operate the server without the cover in place. The chassis cover must be in place to allow proper airflow and prevent overheating.

6-3

Image 52

Contents Super Manual Revision Release Date July 19 About This Manual Manual OrganizationAdvanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents System Safety Bios Chapter Introduction OverviewMotherboard Features Processors MemorySerial ATA PCI Expansion SlotsServer Chassis Features System PowerHard Drive Subsystem Front Control PanelIntel QM77 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-PacificPage Choosing a Setup Location Preparing for SetupUnpacking the System Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Installing the Chassis into a Standard RackInstalling the Chassis into a Telco Rack Telco RackPage Power ResetControl Panel Buttons Power Fail Control Panel LEDsInformational LED Status DescriptionDrive Carrier LEDs HDDPage Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelControl Panel Header Pins Rear I/O PortsInstalling Memory How to Install SO DIMMsOnboard Processor and Heatsink Adding PCI Add-On CardsSO Dimm Socket To RemoveMotherboard Details X9SPV-LN4F/F-3610ME LayoutJumper Description Default Setting Connector DescriptionX9SPV-LN4F/F-3610ME Quick Reference Connector Definitions Power ConnectorsPower Button Reset ButtonPower On LED NMI ButtonEthernet Ports Fan HeadersChassis Intrusion Serial PortsUniversal Serial Bus USB Internal SpeakerLAN Ports LAN1~LAN4 Sgpio Headers Power LED/SpeakerOverheat/Fan Fail LED DOM Power Connector Power Supply SMBus I2C HeaderJumper Settings Bios Write Protect JWP1Explanation of Jumpers Cmos ClearBMC Enable/Disable Watch Dog Enable/DisableUSB Wake-Up JPUSB1 Onboard Indicators Standby Power LED LED1LAN LEDs Ipmi Heartbeat LED LED2Sata and SAS Ports Serial ATA PortsInstalling Software Driver/Tool Installation Display ScreenSuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Control Panel Front and Rear Chassis ViewsRemoving the Chassis Cover Removing the Chassis CoverInstalling Hard Drives System Fans OptionalInstalling 2.5 Hard Drives Hard Drive Configuration Options Installing Hard DrivesInstalling an Expansion Card Locating the Expansion Card ClipInstalling the Expansion Card Power Supply Replacing the Power SupplyPage How To Change the Configuration Data Starting Bios Setup UtilityIntroduction Main Setup How to Start the Setup UtilitySystem Time/System Date Supermicro X9SPV-F/LN4FProcessor System MemoryAdvanced Setup Configurations BOOT FeatureQuiet Boot Bootup Num-LockProcessor and Clock Options Hardware Prefetcher Available when supported by the CPU Active Processor CoresLimit Cpuid Maximum Clock Spread SpectrumCPU PPM Configuration Power Technology Turbo ModeConfig TDP Lock Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Pre-Boot Driver Xhci ModeHS Port #1~#4 Switchable USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings IDO Request Enable Available when supported by the hardware Target Link Speed Available when supported by the hardwareCompliance SOS Available when supported by the hardware Is Disabled Network StackPCI-E Slot 1 Option ROM Onboard LAN Option ROM SelectSuper IO Device Configuration Serial Port 1 Settings / Serial Port 2 SettingsIpv6 PXE Support AutoRemote Access Configuration Console Redirection SettingsRecorder Mode ResolutionLegacy OS Redirection Resolution Redirection After Bios PostConsole Redirection Settings for EMS ACPI ConfigurationHigh Precision Timer Out-of-Band-Mgmt PortIntel Txtlt Configuration Trusted Computing ConfigurationISCSI Configuration Delete Attempts Add an AttemptChange Attempt Order Port Configuration Information Event LogsLink Speed Wake On LANChange SmBIOS Event Log Settings When SEL Full Ipmi SettingsSystem Event Log BMC Network Configuration Update Ipmi LAN ConfigurationConfiguration Source Log EFI Status CodesBoot Security Settings Administrator PasswordUser Password HDD PasswordSave Changes and Reset ExitDiscard Changes and Exit Discard ChangesRestore Defaults Save As User DefaultsRestore User Defaults Boot OverrideAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front