SUPER MICRO Computer 5017P-TLN4F, 5017P-TF user manual IDE/SATA Configuration

Page 70

Chapter 7: BIOS

SLP_S4 Assertion Width

Use this feature to select a minimum assertion width of the SLP_S4 signal. The options are Disabled, 1-2 Seconds, 2-3 Seconds, 3-4 Seconds, and 4-5 Seconds.

IDE/SATA Configuration

When this submenu is selected, the AMI BIOS automatically detects the presence of the SATA Devices and displays the following items:

SATA Controllers

This item enables or disables the on board SATA controller. The options are En- abled and Disabled:

SATA Mode Selection

This item selects the mode for the installed drives. The options are Disabled, IDE Mode, AHCI Mode and RAID Mode. The following are displayed depending on your selection:

IDE Mode

The following items are displayed when IDE Mode is selected:

Serial ATA Port 0~5

This item displays the information detected on the installed SATA drives on the particular SATA port.

AHCI Mode

The following items are displayed when AHCI Mode is selected:

Aggressive LPM Support

This feature Enables or Disables Aggressive Link Power Management support for Cougar Point B0 stepping and later. The options are Enabled and Disabled.

Serial ATA Port 0~5 Hot Plug

Set this item to Enabled to enable hot-plugging for the particular port. The options are Enabled and Disabled.

Serial ATA Port 0~5 Spin Up Device

Set this item to Enabled to enable device spin-up support. The options are Enabled and Disabled.

7-1

Image 70

Contents Super Manual Revision Release Date July 19 About This Manual Manual OrganizationAdvanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents System Safety Bios Chapter Introduction OverviewSerial ATA Motherboard FeaturesProcessors Memory PCI Expansion SlotsHard Drive Subsystem Server Chassis FeaturesSystem Power Front Control PanelIntel QM77 Chipset System Block Diagram Europe Contacting SupermicroHeadquarters Asia-PacificPage Choosing a Setup Location Preparing for SetupUnpacking the System Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Installing the Chassis into a Standard RackInstalling the Chassis into a Telco Rack Telco RackPage Power ResetControl Panel Buttons Informational LED Status Power FailControl Panel LEDs DescriptionDrive Carrier LEDs HDDPage Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelControl Panel Header Pins Rear I/O PortsOnboard Processor and Heatsink Installing MemoryHow to Install SO DIMMs Adding PCI Add-On CardsSO Dimm Socket To RemoveMotherboard Details X9SPV-LN4F/F-3610ME LayoutJumper Description Default Setting Connector DescriptionX9SPV-LN4F/F-3610ME Quick Reference Power Button Connector DefinitionsPower Connectors Reset ButtonPower On LED NMI ButtonChassis Intrusion Ethernet PortsFan Headers Serial PortsUniversal Serial Bus USB Internal SpeakerLAN Ports LAN1~LAN4 Sgpio Headers Power LED/SpeakerOverheat/Fan Fail LED DOM Power Connector Power Supply SMBus I2C HeaderExplanation of Jumpers Jumper SettingsBios Write Protect JWP1 Cmos ClearBMC Enable/Disable Watch Dog Enable/DisableUSB Wake-Up JPUSB1 LAN LEDs Onboard IndicatorsStandby Power LED LED1 Ipmi Heartbeat LED LED2Sata and SAS Ports Serial ATA PortsInstalling Software Driver/Tool Installation Display ScreenSuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Control Panel Front and Rear Chassis ViewsRemoving the Chassis Cover Removing the Chassis CoverInstalling Hard Drives System Fans OptionalInstalling 2.5 Hard Drives Hard Drive Configuration Options Installing Hard DrivesInstalling an Expansion Card Locating the Expansion Card ClipInstalling the Expansion Card Power Supply Replacing the Power SupplyPage How To Change the Configuration Data Starting Bios Setup UtilityIntroduction Main Setup How to Start the Setup UtilityProcessor System Time/System DateSupermicro X9SPV-F/LN4F System MemoryQuiet Boot Advanced Setup ConfigurationsBOOT Feature Bootup Num-LockProcessor and Clock Options Limit Cpuid Maximum Hardware Prefetcher Available when supported by the CPUActive Processor Cores Clock Spread SpectrumConfig TDP Lock CPU PPM Configuration Power TechnologyTurbo Mode Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration HS Port #1~#4 Switchable Xhci Pre-Boot DriverXhci Mode USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings IDO Request Enable Available when supported by the hardware Target Link Speed Available when supported by the hardwarePCI-E Slot 1 Option ROM Compliance SOS Available when supported by the hardwareIs Disabled Network Stack Onboard LAN Option ROM SelectIpv6 PXE Support Super IO Device ConfigurationSerial Port 1 Settings / Serial Port 2 Settings AutoRemote Access Configuration Console Redirection SettingsLegacy OS Redirection Resolution Recorder ModeResolution Redirection After Bios PostHigh Precision Timer Console Redirection Settings for EMSACPI Configuration Out-of-Band-Mgmt PortIntel Txtlt Configuration Trusted Computing ConfigurationISCSI Configuration Delete Attempts Add an AttemptChange Attempt Order Link Speed Port Configuration InformationEvent Logs Wake On LANChange SmBIOS Event Log Settings When SEL Full Ipmi SettingsSystem Event Log Configuration Source BMC Network ConfigurationUpdate Ipmi LAN Configuration Log EFI Status CodesBoot User Password Security SettingsAdministrator Password HDD PasswordDiscard Changes and Exit Save Changes and ResetExit Discard ChangesRestore User Defaults Restore DefaultsSave As User Defaults Boot OverrideAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front