SUPER MICRO Computer 5017P-TLN4F, 5017P-TF user manual Connecting Cables, Connecting Data Cables

Page 30

SUPERSERVER 5017P-TLN4F/TF User's Manual

5-2 Connecting Cables

Now that the motherboard is installed, the next step is to connect the cables to the board. These include the data cables for the peripherals and control panel and the power cables.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully routed to prevent them from blocking the flow of cooling air that moves through the system from front to back. If you need to disconnect any of these cables, you should take care to keep them routed as they were originally after reconnecting them (make sure the red wires connect to the pin 1 locations). The following data cables (with their locations noted) should be connected. (See the layout on page 5-10 for connector locations.)

SATA drive data cables (I-SATA1 ~ I-SATA3)

Control Panel cable (JF1)

Important! Make sure the the cables do not come into contact with the fans.

Connecting Power Cables

The X9SPV-LN4F/F-3610ME has a 24-pin primary power supply connector (JPW1) for connection to the ATX power supply. See Section 5-8 for power connector pin definitions.

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1 for the pin locations of the various front control panel buttons and LED indicators.

All JF1 wires have been bundled into a single cable to simplify this connection. Make sure the red wire plugs into pin 1 as marked on the board. The other end connects to the Control Panel PCB board, located just behind the system status LEDs on the chassis. See Chapter 5 for details and pin descriptions.

5-2

Image 30
Contents Super Manual Revision Release Date July 19 About This Manual Manual OrganizationAdvanced Serverboard Setup Advanced Chassis SetupBios Preface Table of Contents System Safety Bios Chapter Introduction OverviewSerial ATA Motherboard FeaturesProcessors Memory PCI Expansion SlotsHard Drive Subsystem Server Chassis FeaturesSystem Power Front Control PanelIntel QM77 Chipset System Block Diagram Europe Contacting SupermicroHeadquarters Asia-PacificPage Preparing for Setup Choosing a Setup LocationUnpacking the System Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Installing the Chassis into a Standard RackInstalling the Chassis into a Telco Rack Telco RackPage Reset PowerControl Panel Buttons Informational LED Status Power FailControl Panel LEDs DescriptionDrive Carrier LEDs HDDPage Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelControl Panel Header Pins Rear I/O PortsOnboard Processor and Heatsink Installing MemoryHow to Install SO DIMMs Adding PCI Add-On CardsSO Dimm Socket To RemoveMotherboard Details X9SPV-LN4F/F-3610ME LayoutConnector Description Jumper Description Default SettingX9SPV-LN4F/F-3610ME Quick Reference Power Button Connector DefinitionsPower Connectors Reset ButtonPower On LED NMI ButtonChassis Intrusion Ethernet PortsFan Headers Serial PortsInternal Speaker Universal Serial Bus USBLAN Ports LAN1~LAN4 Power LED/Speaker Sgpio HeadersOverheat/Fan Fail LED DOM Power Connector Power Supply SMBus I2C HeaderExplanation of Jumpers Jumper SettingsBios Write Protect JWP1 Cmos ClearWatch Dog Enable/Disable BMC Enable/DisableUSB Wake-Up JPUSB1 LAN LEDs Onboard IndicatorsStandby Power LED LED1 Ipmi Heartbeat LED LED2Sata and SAS Ports Serial ATA PortsInstalling Software Driver/Tool Installation Display ScreenSuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Control Panel Front and Rear Chassis ViewsRemoving the Chassis Cover Removing the Chassis CoverInstalling Hard Drives System Fans OptionalInstalling 2.5 Hard Drives Hard Drive Configuration Options Installing Hard DrivesInstalling an Expansion Card Locating the Expansion Card ClipInstalling the Expansion Card Power Supply Replacing the Power SupplyPage Starting Bios Setup Utility How To Change the Configuration DataIntroduction Main Setup How to Start the Setup UtilityProcessor System Time/System DateSupermicro X9SPV-F/LN4F System MemoryQuiet Boot Advanced Setup ConfigurationsBOOT Feature Bootup Num-LockProcessor and Clock Options Limit Cpuid Maximum Hardware Prefetcher Available when supported by the CPUActive Processor Cores Clock Spread SpectrumConfig TDP Lock CPU PPM Configuration Power TechnologyTurbo Mode Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration HS Port #1~#4 Switchable Xhci Pre-Boot DriverXhci Mode USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings IDO Request Enable Available when supported by the hardware Target Link Speed Available when supported by the hardwarePCI-E Slot 1 Option ROM Compliance SOS Available when supported by the hardwareIs Disabled Network Stack Onboard LAN Option ROM SelectIpv6 PXE Support Super IO Device ConfigurationSerial Port 1 Settings / Serial Port 2 Settings AutoRemote Access Configuration Console Redirection SettingsLegacy OS Redirection Resolution Recorder ModeResolution Redirection After Bios PostHigh Precision Timer Console Redirection Settings for EMSACPI Configuration Out-of-Band-Mgmt PortTrusted Computing Configuration Intel Txtlt ConfigurationISCSI Configuration Add an Attempt Delete AttemptsChange Attempt Order Link Speed Port Configuration InformationEvent Logs Wake On LANChange SmBIOS Event Log Settings Ipmi Settings When SEL FullSystem Event Log Configuration Source BMC Network ConfigurationUpdate Ipmi LAN Configuration Log EFI Status CodesBoot User Password Security SettingsAdministrator Password HDD PasswordDiscard Changes and Exit Save Changes and ResetExit Discard ChangesRestore User Defaults Restore DefaultsSave As User Defaults Boot OverrideAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front