SUPER MICRO Computer 5017P-TF, 5017P-TLN4F user manual Drive Carrier LEDs, Hdd

Page 23

Chapter 3: System Interface

HDD

On the SuperServer 5017P-TLN4F/TF, this LED indicates SATA drive activity when flashing.

Power

Indicates power is being supplied to the system's power supply units. This LED should normally be illuminated when the system is operating.

3-4 Drive Carrier LEDs

Each drive carrier has two LEDs:

•Green: When illuminated, the green LED on the SATA drive carrier indicates drive activity. A connection to the SATA backplane enables this LED to blink on and off when that particular drive is being accessed. Please refer to Chapter 6 for instructions on replacing failed SATA drives.

•Red: When this LED flashes it indicates the drive is rebuilding. When solid on it indicates a SATA drive failure. If a drive fails, you should be notified by your system management software. Please refer to Chapter 6 for instructions on replacing failed drives.

3-3

Image 23

Contents Super Manual Revision Release Date July 19 Manual Organization About This ManualBios Advanced Serverboard SetupAdvanced Chassis Setup Preface Table of Contents System Safety Bios Overview Chapter IntroductionPCI Expansion Slots Motherboard FeaturesProcessors Memory Serial ATAFront Control Panel Server Chassis FeaturesSystem Power Hard Drive SubsystemIntel QM77 Chipset System Block Diagram Asia-Pacific Contacting SupermicroHeadquarters EuropePage Unpacking the System Preparing for SetupChoosing a Setup Location Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureInstalling the Chassis into a Standard Rack Installing the System into a RackTelco Rack Installing the Chassis into a Telco RackPage Control Panel Buttons ResetPower Description Power FailControl Panel LEDs Informational LED StatusHDD Drive Carrier LEDsPage Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsChapter Advanced Motherboard Setup Connecting the Control Panel Connecting CablesConnecting Data Cables Connecting Power CablesRear I/O Ports Control Panel Header PinsAdding PCI Add-On Cards Installing MemoryHow to Install SO DIMMs Onboard Processor and HeatsinkTo Remove SO Dimm SocketX9SPV-LN4F/F-3610ME Layout Motherboard DetailsX9SPV-LN4F/F-3610ME Quick Reference Connector DescriptionJumper Description Default Setting Reset Button Connector DefinitionsPower Connectors Power ButtonNMI Button Power On LEDSerial Ports Ethernet PortsFan Headers Chassis IntrusionLAN Ports LAN1~LAN4 Internal SpeakerUniversal Serial Bus USB Overheat/Fan Fail LED Power LED/SpeakerSgpio Headers Power Supply SMBus I2C Header DOM Power ConnectorCmos Clear Jumper SettingsBios Write Protect JWP1 Explanation of JumpersUSB Wake-Up JPUSB1 Watch Dog Enable/DisableBMC Enable/Disable Ipmi Heartbeat LED LED2 Onboard IndicatorsStandby Power LED LED1 LAN LEDsSerial ATA Ports Sata and SAS PortsDriver/Tool Installation Display Screen Installing SoftwareSuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Front and Rear Chassis Views Control PanelRemoving the Chassis Cover Removing the Chassis CoverSystem Fans Optional Installing Hard DrivesInstalling 2.5 Hard Drives Installing Hard Drives Hard Drive Configuration OptionsLocating the Expansion Card Clip Installing an Expansion CardInstalling the Expansion Card Replacing the Power Supply Power SupplyPage Introduction Starting Bios Setup UtilityHow To Change the Configuration Data How to Start the Setup Utility Main SetupSystem Memory System Time/System DateSupermicro X9SPV-F/LN4F ProcessorBootup Num-Lock Advanced Setup ConfigurationsBOOT Feature Quiet BootProcessor and Clock Options Clock Spread Spectrum Hardware Prefetcher Available when supported by the CPUActive Processor Cores Limit Cpuid MaximumLong Duration Power Limit CPU PPM Configuration Power TechnologyTurbo Mode Config TDP LockAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration USB Ports Per-Port Disable Control Xhci Pre-Boot DriverXhci Mode HS Port #1~#4 SwitchableIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings Target Link Speed Available when supported by the hardware IDO Request Enable Available when supported by the hardwareOnboard LAN Option ROM Select Compliance SOS Available when supported by the hardwareIs Disabled Network Stack PCI-E Slot 1 Option ROMAuto Super IO Device ConfigurationSerial Port 1 Settings / Serial Port 2 Settings Ipv6 PXE SupportConsole Redirection Settings Remote Access ConfigurationRedirection After Bios Post Recorder ModeResolution Legacy OS Redirection ResolutionOut-of-Band-Mgmt Port Console Redirection Settings for EMSACPI Configuration High Precision TimerISCSI Configuration Trusted Computing ConfigurationIntel Txtlt Configuration Change Attempt Order Add an AttemptDelete Attempts Wake On LAN Port Configuration InformationEvent Logs Link SpeedChange SmBIOS Event Log Settings System Event Log Ipmi SettingsWhen SEL Full Log EFI Status Codes BMC Network ConfigurationUpdate Ipmi LAN Configuration Configuration SourceBoot HDD Password Security SettingsAdministrator Password User PasswordDiscard Changes Save Changes and ResetExit Discard Changes and ExitBoot Override Restore DefaultsSave As User Defaults Restore User DefaultsRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front