SUPER MICRO Computer 5017P-TF, 5017P-TLN4F user manual Power On LED, NMI Button

Page 37

Chapter 5: Advanced Motherboard Setup

NIC2 LED

The LED connections for LAN2 are on pins 9 and 10 of JF1. Attach an LED cable to display network activ- ity. See the table on the right for pin definitions.

NIC1 LED

The LED connections for LAN1 are on pins 11 and 12 of JF1. Attach an LED cable to display network activ- ity. See the table on the right for pin definitions.

HDD LED

The HDD LED connection is located on pins 13 and 14 of JF1. Attach a hard drive LED cable here to display disk activity (for any hard drive ac- tivities on the system, including Serial ATA and IDE). See the table on the right for pin definitions.

Power On LED

The Power On LED connector is lo- cated on pins 15 and 16 of JF1. This connection is used to provide LED indication of power being supplied to the system. See the table on the right for pin definitions.

NMI Button

The non-maskable interrupt button header is located on pins 19 and 20 of JF1. See the table on the right for pin definitions.

NIC2 LED

Pin Definitions (JF1)

Pin# Definition

9Vcc

10Ground

NIC1 LED

Pin Definitions (JF1)

Pin# Definition

11Vcc

12Ground

HDD LED

Pin Definitions (JF1)

Pin# Definition

13Vcc

14HD Active

Power LED

Pin Definitions (JF1)

Pin# Definition

15+3.3V

16Control

NMI Button

Pin Definitions (JF1)

Pin# Definition

19Control

20Ground

5-9

Image 37

Contents Super Manual Revision Release Date July 19 Manual Organization About This ManualAdvanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents System Safety Bios Overview Chapter IntroductionProcessors Memory Motherboard FeaturesSerial ATA PCI Expansion SlotsSystem Power Server Chassis FeaturesHard Drive Subsystem Front Control PanelIntel QM77 Chipset System Block Diagram Headquarters Contacting SupermicroEurope Asia-PacificPage Choosing a Setup Location Preparing for SetupUnpacking the System Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureInstalling the Chassis into a Standard Rack Installing the System into a RackTelco Rack Installing the Chassis into a Telco RackPage Power ResetControl Panel Buttons Control Panel LEDs Power FailInformational LED Status DescriptionHDD Drive Carrier LEDsPage Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsChapter Advanced Motherboard Setup Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control PanelRear I/O Ports Control Panel Header PinsHow to Install SO DIMMs Installing MemoryOnboard Processor and Heatsink Adding PCI Add-On CardsTo Remove SO Dimm SocketX9SPV-LN4F/F-3610ME Layout Motherboard DetailsJumper Description Default Setting Connector DescriptionX9SPV-LN4F/F-3610ME Quick Reference Power Connectors Connector DefinitionsPower Button Reset ButtonNMI Button Power On LEDFan Headers Ethernet PortsChassis Intrusion Serial PortsUniversal Serial Bus USB Internal SpeakerLAN Ports LAN1~LAN4 Sgpio Headers Power LED/SpeakerOverheat/Fan Fail LED Power Supply SMBus I2C Header DOM Power ConnectorBios Write Protect JWP1 Jumper SettingsExplanation of Jumpers Cmos ClearBMC Enable/Disable Watch Dog Enable/DisableUSB Wake-Up JPUSB1 Standby Power LED LED1 Onboard IndicatorsLAN LEDs Ipmi Heartbeat LED LED2Serial ATA Ports Sata and SAS PortsDriver/Tool Installation Display Screen Installing SoftwareSuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Front and Rear Chassis Views Control PanelRemoving the Chassis Cover Removing the Chassis CoverSystem Fans Optional Installing Hard DrivesInstalling 2.5 Hard Drives Installing Hard Drives Hard Drive Configuration OptionsLocating the Expansion Card Clip Installing an Expansion CardInstalling the Expansion Card Replacing the Power Supply Power SupplyPage How To Change the Configuration Data Starting Bios Setup UtilityIntroduction How to Start the Setup Utility Main SetupSupermicro X9SPV-F/LN4F System Time/System DateProcessor System MemoryBOOT Feature Advanced Setup ConfigurationsQuiet Boot Bootup Num-LockProcessor and Clock Options Active Processor Cores Hardware Prefetcher Available when supported by the CPULimit Cpuid Maximum Clock Spread SpectrumTurbo Mode CPU PPM Configuration Power TechnologyConfig TDP Lock Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Mode Xhci Pre-Boot DriverHS Port #1~#4 Switchable USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings Target Link Speed Available when supported by the hardware IDO Request Enable Available when supported by the hardwareIs Disabled Network Stack Compliance SOS Available when supported by the hardwarePCI-E Slot 1 Option ROM Onboard LAN Option ROM SelectSerial Port 1 Settings / Serial Port 2 Settings Super IO Device ConfigurationIpv6 PXE Support AutoConsole Redirection Settings Remote Access ConfigurationResolution Recorder ModeLegacy OS Redirection Resolution Redirection After Bios PostACPI Configuration Console Redirection Settings for EMSHigh Precision Timer Out-of-Band-Mgmt PortIntel Txtlt Configuration Trusted Computing ConfigurationISCSI Configuration Delete Attempts Add an AttemptChange Attempt Order Event Logs Port Configuration InformationLink Speed Wake On LANChange SmBIOS Event Log Settings When SEL Full Ipmi SettingsSystem Event Log Update Ipmi LAN Configuration BMC Network ConfigurationConfiguration Source Log EFI Status CodesBoot Administrator Password Security SettingsUser Password HDD PasswordExit Save Changes and ResetDiscard Changes and Exit Discard ChangesSave As User Defaults Restore DefaultsRestore User Defaults Boot OverrideRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front