SUPER MICRO Computer 5017P-TF Remote Access Configuration, Console Redirection Settings

Page 77

SUPERSERVER 5017P-TLN4F/TF User's Manual

Remote Access Configuration

COM1, COM2, SOL Console Redirection

Use this feature to enable console redirection for COM1, and COM2 ports. The options are Enabled and Disabled. The default for COM1 and COM2 is Disabled. The default for SOL is Enabled.

Console Redirection Settings

This feature allows the user to specify how the host computer will exchange data with the client computer, which is the remote computer used by the user.

Terminal Type

This feature allows the user to select the target terminal emulation type for Con- sole Redirection. Select VT100 to use the ASCII character set. Select VT100+ to add color and function key support. Select ANSI to use the extended ASCII character set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.

Bits Per Second

This item sets the transmission speed for a serial port used in Console Redirec- tion. Make sure that the same speed is used in the host computer and the client computer. A lower transmission speed may be required for long and busy lines. The options are 9600, 19200, 38400, 57600, and 115200 (bits per second).

Data Bits

Use this feature to set the data transmission size for Console Redirection. The options are 7 and 8 (Bits).

Parity

A parity bit can be sent along with regular data bits to detect data transmission errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits is odd. Select None if you do not want to send a parity bit with your data bits in transmission. Select Mark to add mark as a parity bit to be sent along with the data bits. Select Space to add a Space as a parity bit to be sent with your data bits. The options are None, Even, Odd, Mark, and Space.

Stop Bits

A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial data communication. Select 2 Stop Bits if slower devices are used. The options are 1 and 2.

7-18

Image 77
Contents Super Manual Revision Release Date July 19 Manual Organization About This ManualBios Advanced Serverboard SetupAdvanced Chassis Setup Preface Table of Contents System Safety Bios Overview Chapter IntroductionProcessors Memory Motherboard FeaturesSerial ATA PCI Expansion SlotsSystem Power Server Chassis FeaturesHard Drive Subsystem Front Control PanelIntel QM77 Chipset System Block Diagram Headquarters Contacting SupermicroEurope Asia-PacificPage Unpacking the System Preparing for SetupChoosing a Setup Location Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureInstalling the Chassis into a Standard Rack Installing the System into a RackTelco Rack Installing the Chassis into a Telco RackPage Control Panel Buttons ResetPower Control Panel LEDs Power FailInformational LED Status DescriptionHDD Drive Carrier LEDsPage Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsChapter Advanced Motherboard Setup Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control PanelRear I/O Ports Control Panel Header PinsHow to Install SO DIMMs Installing MemoryOnboard Processor and Heatsink Adding PCI Add-On CardsTo Remove SO Dimm SocketX9SPV-LN4F/F-3610ME Layout Motherboard DetailsX9SPV-LN4F/F-3610ME Quick Reference Connector DescriptionJumper Description Default Setting Power Connectors Connector DefinitionsPower Button Reset ButtonNMI Button Power On LEDFan Headers Ethernet PortsChassis Intrusion Serial PortsLAN Ports LAN1~LAN4 Internal SpeakerUniversal Serial Bus USB Overheat/Fan Fail LED Power LED/SpeakerSgpio Headers Power Supply SMBus I2C Header DOM Power ConnectorBios Write Protect JWP1 Jumper SettingsExplanation of Jumpers Cmos ClearUSB Wake-Up JPUSB1 Watch Dog Enable/DisableBMC Enable/Disable Standby Power LED LED1 Onboard IndicatorsLAN LEDs Ipmi Heartbeat LED LED2Serial ATA Ports Sata and SAS PortsDriver/Tool Installation Display Screen Installing SoftwareSuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Front and Rear Chassis Views Control PanelRemoving the Chassis Cover Removing the Chassis CoverSystem Fans Optional Installing Hard DrivesInstalling 2.5 Hard Drives Installing Hard Drives Hard Drive Configuration OptionsLocating the Expansion Card Clip Installing an Expansion CardInstalling the Expansion Card Replacing the Power Supply Power SupplyPage Introduction Starting Bios Setup UtilityHow To Change the Configuration Data How to Start the Setup Utility Main SetupSupermicro X9SPV-F/LN4F System Time/System DateProcessor System MemoryBOOT Feature Advanced Setup ConfigurationsQuiet Boot Bootup Num-LockProcessor and Clock Options Active Processor Cores Hardware Prefetcher Available when supported by the CPULimit Cpuid Maximum Clock Spread SpectrumTurbo Mode CPU PPM Configuration Power TechnologyConfig TDP Lock Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Mode Xhci Pre-Boot DriverHS Port #1~#4 Switchable USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings Target Link Speed Available when supported by the hardware IDO Request Enable Available when supported by the hardwareIs Disabled Network Stack Compliance SOS Available when supported by the hardwarePCI-E Slot 1 Option ROM Onboard LAN Option ROM SelectSerial Port 1 Settings / Serial Port 2 Settings Super IO Device ConfigurationIpv6 PXE Support AutoConsole Redirection Settings Remote Access ConfigurationResolution Recorder ModeLegacy OS Redirection Resolution Redirection After Bios PostACPI Configuration Console Redirection Settings for EMSHigh Precision Timer Out-of-Band-Mgmt PortISCSI Configuration Trusted Computing ConfigurationIntel Txtlt Configuration Change Attempt Order Add an AttemptDelete Attempts Event Logs Port Configuration InformationLink Speed Wake On LANChange SmBIOS Event Log Settings System Event Log Ipmi SettingsWhen SEL Full Update Ipmi LAN Configuration BMC Network ConfigurationConfiguration Source Log EFI Status CodesBoot Administrator Password Security SettingsUser Password HDD PasswordExit Save Changes and ResetDiscard Changes and Exit Discard ChangesSave As User Defaults Restore DefaultsRestore User Defaults Boot OverrideRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front