SUPER MICRO Computer 5017P-TLN4F IDO Request Enable Available when supported by the hardware

Page 74

Chapter 7: BIOS

Configuration Request, permitting access to Extended Functions in an ARI device immediately below the port. The options are Disabled and Enabled.

AtomicOp Requester Enable (Available when supported by the hardware)

When set to Enabled, this feature initiates AtomicOp requests only if Bus Mas- ter Enable bit is in the Command Register set. The options are Disabled and Enabled.

AtomicOp Egress Blocking (Available when supported by the hardware)

When set to Enabled, this feature blocks outbound AtomicOp Requests via Egress ports. The options are Disabled and Enabled.

IDO Request Enable (Available when supported by the hardware)

When set to Enabled, this feature permits setting the number of ID-Based Or- dering (IDO) bit (Attribute[2]) requests to be initiated. The options are Disabled and Enabled.

IDO Completion Enable (Available when supported by the hardware)

When set to Enabled, this feature permits setting the number of ID-Based Or- dering (IDO) bit (Attribute[2]) requests to be initiated. The options are Disabled and Enabled.

LTR Mechanism Enable (Available when supported by the hardware)

When set to Enabled, this feature enables the Latency Tolerance Reporting mechanism. The options are Disabled and Enabled.

End-End TLP Prefix Blocking (Available when supported by the hardware)

When set to Enabled, this feature blocks forwarding of TLPs containing End-End TLP prefixes.

Target Link Speed (Available when supported by the hardware)

When set to Force to 2.5 or 5.0 GT/s, this feature sets an upper limit on the link operational speed of downstream ports by restricting the values advertised by the upstream component in its training sequences. When set to Auto, HW initialized data will be used. The options are Auto, Force to 2.5 GT/s, and Force to 5.0 GT/s.

Clock Power management (Available when supported by the hardware)

When set to Enabled, this feature permits the device to use CLKREQ# signal for power management of link clock in accordance to protocol defined in appropriate form factor specification. The options are Disabled and Enabled.

7-1

Image 74

Contents Super Manual Revision Release Date July 19 About This Manual Manual OrganizationBios Advanced Serverboard SetupAdvanced Chassis Setup Preface Table of Contents System Safety Bios Chapter Introduction OverviewSerial ATA Motherboard FeaturesProcessors Memory PCI Expansion SlotsHard Drive Subsystem Server Chassis FeaturesSystem Power Front Control PanelIntel QM77 Chipset System Block Diagram Europe Contacting SupermicroHeadquarters Asia-PacificPage Unpacking the System Preparing for SetupChoosing a Setup Location Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Installing the Chassis into a Standard RackInstalling the Chassis into a Telco Rack Telco RackPage Control Panel Buttons ResetPower Informational LED Status Power FailControl Panel LEDs DescriptionDrive Carrier LEDs HDDPage Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup Connecting Power Cables Connecting CablesConnecting Data Cables Connecting the Control PanelControl Panel Header Pins Rear I/O PortsOnboard Processor and Heatsink Installing MemoryHow to Install SO DIMMs Adding PCI Add-On CardsSO Dimm Socket To RemoveMotherboard Details X9SPV-LN4F/F-3610ME LayoutX9SPV-LN4F/F-3610ME Quick Reference Connector DescriptionJumper Description Default Setting Power Button Connector DefinitionsPower Connectors Reset ButtonPower On LED NMI ButtonChassis Intrusion Ethernet PortsFan Headers Serial PortsLAN Ports LAN1~LAN4 Internal SpeakerUniversal Serial Bus USB Overheat/Fan Fail LED Power LED/SpeakerSgpio Headers DOM Power Connector Power Supply SMBus I2C HeaderExplanation of Jumpers Jumper SettingsBios Write Protect JWP1 Cmos ClearUSB Wake-Up JPUSB1 Watch Dog Enable/DisableBMC Enable/Disable LAN LEDs Onboard IndicatorsStandby Power LED LED1 Ipmi Heartbeat LED LED2Sata and SAS Ports Serial ATA PortsInstalling Software Driver/Tool Installation Display ScreenSuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Control Panel Front and Rear Chassis ViewsRemoving the Chassis Cover Removing the Chassis CoverInstalling Hard Drives System Fans OptionalInstalling 2.5 Hard Drives Hard Drive Configuration Options Installing Hard DrivesInstalling an Expansion Card Locating the Expansion Card ClipInstalling the Expansion Card Power Supply Replacing the Power SupplyPage Introduction Starting Bios Setup UtilityHow To Change the Configuration Data Main Setup How to Start the Setup UtilityProcessor System Time/System DateSupermicro X9SPV-F/LN4F System MemoryQuiet Boot Advanced Setup ConfigurationsBOOT Feature Bootup Num-LockProcessor and Clock Options Limit Cpuid Maximum Hardware Prefetcher Available when supported by the CPUActive Processor Cores Clock Spread SpectrumConfig TDP Lock CPU PPM Configuration Power TechnologyTurbo Mode Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration HS Port #1~#4 Switchable Xhci Pre-Boot DriverXhci Mode USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings IDO Request Enable Available when supported by the hardware Target Link Speed Available when supported by the hardwarePCI-E Slot 1 Option ROM Compliance SOS Available when supported by the hardwareIs Disabled Network Stack Onboard LAN Option ROM SelectIpv6 PXE Support Super IO Device ConfigurationSerial Port 1 Settings / Serial Port 2 Settings AutoRemote Access Configuration Console Redirection SettingsLegacy OS Redirection Resolution Recorder ModeResolution Redirection After Bios PostHigh Precision Timer Console Redirection Settings for EMSACPI Configuration Out-of-Band-Mgmt PortISCSI Configuration Trusted Computing ConfigurationIntel Txtlt Configuration Change Attempt Order Add an AttemptDelete Attempts Link Speed Port Configuration InformationEvent Logs Wake On LANChange SmBIOS Event Log Settings System Event Log Ipmi SettingsWhen SEL Full Configuration Source BMC Network ConfigurationUpdate Ipmi LAN Configuration Log EFI Status CodesBoot User Password Security SettingsAdministrator Password HDD PasswordDiscard Changes and Exit Save Changes and ResetExit Discard ChangesRestore User Defaults Restore DefaultsSave As User Defaults Boot OverrideAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front