SUPER MICRO Computer 5017P-TF, 5017P-TLN4F Chapter System Safety, Electrical Safety Precautions

Page 25

Chapter 4: System Safety

Chapter 4

System Safety

4-1 Electrical Safety Precautions

!

Basic electrical safety precautions should be followed to protect yourself from harm and the SuperServer 5017P-TLN4F/TF from damage:

Be aware of the locations of the power on/off switch on the chassis as well as the room's emergency power-off switch, disconnection switch or electrical outlet. If an electrical accident occurs, you can then quickly remove power from the system.

Do not work alone when working with high voltage components.

Power should always be disconnected from the system when removing or install- ing main system components, such as the serverboard and memory modules.

When disconnecting power, you should first power down the system with the operating system first and then unplug the power cords of all the power supply units in the system.

When working around exposed electrical circuits, another person who is familiar with the power-off controls should be nearby to switch off the power if neces- sary.

Use only one hand when working with powered-on electrical equipment. This is to avoid making a complete circuit, which will cause electrical shock. Use extreme caution when using metal tools, which can easily damage any electrical components or circuit boards they come into contact with.

Do not use mats designed to decrease static electrical discharge as protection from electrical shock. Instead, use rubber mats that have been specifically designed as electrical insulators.

The power supply power cords must include a grounding plug and must be plugged into grounded electrical outlets.

4-1

Image 25
Contents Super Manual Revision Release Date July 19 Manual Organization About This ManualAdvanced Chassis Setup Advanced Serverboard SetupBios Preface Table of Contents System Safety Bios Overview Chapter IntroductionProcessors Memory Motherboard FeaturesSerial ATA PCI Expansion SlotsSystem Power Server Chassis FeaturesHard Drive Subsystem Front Control PanelIntel QM77 Chipset System Block Diagram Headquarters Contacting SupermicroEurope Asia-PacificPage Choosing a Setup Location Preparing for SetupUnpacking the System Server Precautions Rack PrecautionsRack Mounting Considerations Ambient Operating TemperatureInstalling the Chassis into a Standard Rack Installing the System into a RackTelco Rack Installing the Chassis into a Telco RackPage Power ResetControl Panel Buttons Control Panel LEDs Power FailInformational LED Status DescriptionHDD Drive Carrier LEDsPage Electrical Safety Precautions Chapter System SafetyGeneral Safety Precautions ESD Precautions Installing the Onboard Battery Operating PrecautionsChapter Advanced Motherboard Setup Connecting Data Cables Connecting CablesConnecting Power Cables Connecting the Control PanelRear I/O Ports Control Panel Header PinsHow to Install SO DIMMs Installing MemoryOnboard Processor and Heatsink Adding PCI Add-On CardsTo Remove SO Dimm SocketX9SPV-LN4F/F-3610ME Layout Motherboard DetailsJumper Description Default Setting Connector DescriptionX9SPV-LN4F/F-3610ME Quick Reference Power Connectors Connector DefinitionsPower Button Reset ButtonNMI Button Power On LEDFan Headers Ethernet PortsChassis Intrusion Serial PortsUniversal Serial Bus USB Internal SpeakerLAN Ports LAN1~LAN4 Sgpio Headers Power LED/SpeakerOverheat/Fan Fail LED Power Supply SMBus I2C Header DOM Power ConnectorBios Write Protect JWP1 Jumper SettingsExplanation of Jumpers Cmos ClearBMC Enable/Disable Watch Dog Enable/DisableUSB Wake-Up JPUSB1 Standby Power LED LED1 Onboard IndicatorsLAN LEDs Ipmi Heartbeat LED LED2Serial ATA Ports Sata and SAS PortsDriver/Tool Installation Display Screen Installing SoftwareSuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Front and Rear Chassis Views Control PanelRemoving the Chassis Cover Removing the Chassis CoverSystem Fans Optional Installing Hard DrivesInstalling 2.5 Hard Drives Installing Hard Drives Hard Drive Configuration OptionsLocating the Expansion Card Clip Installing an Expansion CardInstalling the Expansion Card Replacing the Power Supply Power SupplyPage How To Change the Configuration Data Starting Bios Setup UtilityIntroduction How to Start the Setup Utility Main SetupSupermicro X9SPV-F/LN4F System Time/System DateProcessor System MemoryBOOT Feature Advanced Setup ConfigurationsQuiet Boot Bootup Num-LockProcessor and Clock Options Active Processor Cores Hardware Prefetcher Available when supported by the CPULimit Cpuid Maximum Clock Spread SpectrumTurbo Mode CPU PPM Configuration Power TechnologyConfig TDP Lock Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Mode Xhci Pre-Boot DriverHS Port #1~#4 Switchable USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings Target Link Speed Available when supported by the hardware IDO Request Enable Available when supported by the hardwareIs Disabled Network Stack Compliance SOS Available when supported by the hardwarePCI-E Slot 1 Option ROM Onboard LAN Option ROM SelectSerial Port 1 Settings / Serial Port 2 Settings Super IO Device ConfigurationIpv6 PXE Support AutoConsole Redirection Settings Remote Access ConfigurationResolution Recorder ModeLegacy OS Redirection Resolution Redirection After Bios PostACPI Configuration Console Redirection Settings for EMSHigh Precision Timer Out-of-Band-Mgmt PortIntel Txtlt Configuration Trusted Computing ConfigurationISCSI Configuration Delete Attempts Add an AttemptChange Attempt Order Event Logs Port Configuration InformationLink Speed Wake On LANChange SmBIOS Event Log Settings When SEL Full Ipmi SettingsSystem Event Log Update Ipmi LAN Configuration BMC Network ConfigurationConfiguration Source Log EFI Status CodesBoot Administrator Password Security SettingsUser Password HDD PasswordExit Save Changes and ResetDiscard Changes and Exit Discard ChangesSave As User Defaults Restore DefaultsRestore User Defaults Boot OverrideRecoverable Post Error Beep Codes Appendix a Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front