SUPER MICRO Computer 5017P-TLN4F, 5017P-TF user manual Bios

Page 8

SUPERSERVER 5017P-TLN4F/TF User's Manual

6-2

Control Panel

6-2

6-3

Removing the Chassis Cover

6-3

6-4

System Fans

6-4

6-5

Installing Hard Drives

6-4

6-6

Installing an Expansion Card

6-6

6-7

Power Supply

6-8

 

Replacing the Power Supply

6-8

Chapter 7 BIOS

7-1

Introduction

7-1

 

Starting BIOS Setup Utility

7-1

 

How To Change the Configuration Data

7-1

 

How to Start the Setup Utility

7-2

7-2

Main Setup

7-2

7-3

Advanced Setup Configurations

7-4

 

NIC Configuration

7-23

7-4

Event Logs

7-23

7-5

IPMI Settings

7-25

7-6

Boot

7-27

7-7

Security Settings

7-28

7-8

Exit

7-29

Appendix A POST Error Beep Codes

Appendix B System Specifications

viii

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Super Manual Revision Release Date July 19 About This Manual Manual OrganizationBios Advanced Serverboard SetupAdvanced Chassis Setup Preface Table of Contents System Safety Bios Chapter Introduction OverviewMotherboard Features Processors MemorySerial ATA PCI Expansion SlotsServer Chassis Features System PowerHard Drive Subsystem Front Control PanelIntel QM77 Chipset System Block Diagram Contacting Supermicro HeadquartersEurope Asia-PacificPage Unpacking the System Preparing for SetupChoosing a Setup Location Rack Precautions Server PrecautionsAmbient Operating Temperature Rack Mounting ConsiderationsInstalling the System into a Rack Installing the Chassis into a Standard RackInstalling the Chassis into a Telco Rack Telco RackPage Control Panel Buttons ResetPower Power Fail Control Panel LEDsInformational LED Status DescriptionDrive Carrier LEDs HDDPage Chapter System Safety Electrical Safety PrecautionsGeneral Safety Precautions ESD Precautions Operating Precautions Installing the Onboard BatteryChapter Advanced Motherboard Setup Connecting Cables Connecting Data CablesConnecting Power Cables Connecting the Control PanelControl Panel Header Pins Rear I/O PortsInstalling Memory How to Install SO DIMMsOnboard Processor and Heatsink Adding PCI Add-On CardsSO Dimm Socket To RemoveMotherboard Details X9SPV-LN4F/F-3610ME LayoutX9SPV-LN4F/F-3610ME Quick Reference Connector DescriptionJumper Description Default Setting Connector Definitions Power ConnectorsPower Button Reset ButtonPower On LED NMI ButtonEthernet Ports Fan HeadersChassis Intrusion Serial PortsLAN Ports LAN1~LAN4 Internal SpeakerUniversal Serial Bus USB Overheat/Fan Fail LED Power LED/SpeakerSgpio Headers DOM Power Connector Power Supply SMBus I2C HeaderJumper Settings Bios Write Protect JWP1Explanation of Jumpers Cmos ClearUSB Wake-Up JPUSB1 Watch Dog Enable/DisableBMC Enable/Disable Onboard Indicators Standby Power LED LED1LAN LEDs Ipmi Heartbeat LED LED2Sata and SAS Ports Serial ATA PortsInstalling Software Driver/Tool Installation Display ScreenSuperDoctor Supero Doctor III Interface Display Screen Remote Control Advanced Motherboard Setup Page Control Panel Front and Rear Chassis ViewsRemoving the Chassis Cover Removing the Chassis CoverInstalling Hard Drives System Fans OptionalInstalling 2.5 Hard Drives Hard Drive Configuration Options Installing Hard DrivesInstalling an Expansion Card Locating the Expansion Card ClipInstalling the Expansion Card Power Supply Replacing the Power SupplyPage Introduction Starting Bios Setup UtilityHow To Change the Configuration Data Main Setup How to Start the Setup UtilitySystem Time/System Date Supermicro X9SPV-F/LN4FProcessor System MemoryAdvanced Setup Configurations BOOT FeatureQuiet Boot Bootup Num-LockProcessor and Clock Options Hardware Prefetcher Available when supported by the CPU Active Processor CoresLimit Cpuid Maximum Clock Spread SpectrumCPU PPM Configuration Power Technology Turbo ModeConfig TDP Lock Long Duration Power LimitAdvanced Chipset Control System Agent SA Configuration PCH-IO Configuration Xhci Pre-Boot Driver Xhci ModeHS Port #1~#4 Switchable USB Ports Per-Port Disable ControlIDE/SATA Configuration PCIe/PCI/PnP Configuration PCI Express Settings PCI Express GEN 2 Settings IDO Request Enable Available when supported by the hardware Target Link Speed Available when supported by the hardwareCompliance SOS Available when supported by the hardware Is Disabled Network StackPCI-E Slot 1 Option ROM Onboard LAN Option ROM SelectSuper IO Device Configuration Serial Port 1 Settings / Serial Port 2 SettingsIpv6 PXE Support AutoRemote Access Configuration Console Redirection SettingsRecorder Mode ResolutionLegacy OS Redirection Resolution Redirection After Bios PostConsole Redirection Settings for EMS ACPI ConfigurationHigh Precision Timer Out-of-Band-Mgmt PortISCSI Configuration Trusted Computing ConfigurationIntel Txtlt Configuration Change Attempt Order Add an AttemptDelete Attempts Port Configuration Information Event LogsLink Speed Wake On LANChange SmBIOS Event Log Settings System Event Log Ipmi SettingsWhen SEL Full BMC Network Configuration Update Ipmi LAN ConfigurationConfiguration Source Log EFI Status CodesBoot Security Settings Administrator PasswordUser Password HDD PasswordSave Changes and Reset ExitDiscard Changes and Exit Discard ChangesRestore Defaults Save As User DefaultsRestore User Defaults Boot OverrideAppendix a Post Error Beep Codes Recoverable Post Error Beep CodesPage Appendix B System Specifications System Input Requirements Appendix B System Specifications From front
Top Page Image Contents