Basic Connections/Auto Setup

Front Panel LAMP

DVD

VCR

1When the light is on, DVD is operating.

2When the light is on, CD is operating.

You will need to connect the DVD-VCR to a TV and run Auto Setup. The Auto Setup will automatically search for channels and then set your DVD-VCR's internal clock.

NOTES:

•See Appendix A for Advanced Connections.

•Standard RF or Line connection between your TV

and DVD-VCR are required to run DVD+VCR setup menu, even if you connect S-Video or Component Video Output for a better picture quality.

1Connect the RF Antenna Cable to your DVD-VCR Connect an external indoor/outdoor antenna or wall outlet antenna cable to the Ant-In jack on the rear panel. (RF Through Only)

4Turn On your DVD-VCR

Turn on the power by pressing the POWER button on the remote control or on the front panel of the unit.

5Turn On your TV

Turn on the TV by pressing the POWER button on the TV remote control.

6Set the TV to Line

Set your TV to its Line Input.

Stereo Connections

S-Video/Component Video

Connections (for DVD)

Use the S-Video or Component Video connection method only for the DVD player. The tuner and VCR can still be viewed through the RF or line inputs.

To activate your alternative (S-Video or Component) video selection, follow the “Alt Video Out” instructions on page 18. Keep in mind that you can choose either S-Video or Component only, but not both. A superior video quality can be obtained when watching a DVD on your DVD-VCR if your TV is equipped with S-Video or Component Video inputs.

1Connect S-Video Out to TV

Using an S-Video cable, connect the S-VIDEO OUT on the rear panel of your DVD-VCR to the S-Video Input on your TV.

From Antenna or Cable

To TV’s Antenna Input

You can connect your DVD-VCR to your home stereo system or stereo TV and enjoy stereo sound when watching a movie or TV.

Insert Batteries into Remote

•Remove the battery cover on the remote

•Insert two 1.5V “AAA” batteries as shown, making sure of the correct polarities(+/-)

•Slide the cover back onto remote.

2Connect your DVD-VCR to a TV

RF Connection

Using the RF antenna cable, connect the OUT jack (TO TV) on the rear panel of your DVD-VCR to your TV’s Antenna Input.

Line Connection

Using an RCA-type audio/video cable (red, white, yellow), connect the LINE OUT jacks on the rear panel of your DVD-VCR to your TV's Line In jacks. Use the three cables as follows: red for right audio, white for left audio, and yellow for video.

NOTE: If your TV is equipped with RCA jacks, it is better to use the Line Connection method.

3Plug In

Your DVD-VCR's power should be plugged into a standard 120V/60Hz wall outlet. Avoid pressing any buttons on the remote control or on the unit during an Auto Setup. It would take about 7 minutes. After Auto Setup is complete Operate your DVD-VCR. In case Auto Clock set fails to locate a channel to set the clock, you should set the clock manually. See page 11.

1Connect DVD-VCR to Stereo

Using RCA cables, connect the Line Out Left and Right Audio jacks on the rear panel of the DVD-VCR to the Auxiliary Inputs on your stereo receiver. Connect the Video Output also in case you are using a stereo TV.

2Set Stereo to Auxiliary Mode

Set your stereo receiver or TV to either “Aux” or “Tape” regardless of which line input you are using for your particular device.

3Play a Tape

Insert a DVD or Hi-Fi stereo videotape into your system. Be sure to adjust the volume on your stereo receiver or TV. Audio will be heard through your stereo speakers

•If there is no stereo sound even after you have inserted a Hi-Fi stereo videotape, press the AUDIO button until “Hi-Fi” appears on the on-screen display.

2Connect Component Video Out to TV Using a component video cable, connect the COMPONENT VIDEO OUT (Y, Pb, Pr) on the rear panel of your DVD-VCR to the Component Video Input on your TV. .

To Component Video Input

on Your TV

3Connect Audio Out (DVD only)

Using RCA audio cables, connect the LEFT/RIGHT Line Out jacks on the rear panel of your DVD/VCR to the LEFT/RIGHT Audio Line In jacks on your TV.

•When connecting your DVD-VCR to a TV with the S-Video or Component Video Output, make sure that you use these Line Out jacks.

•To activate your connection, see “Alt Video Out” on page 18.

To Left/Right Audio Inputs

on Your TV

ENG-6

ENG-7