Mitsubishi Electronics WD-52627 manual Receiver AVR Input Learn Screen, Receiver AVR Learn Screen

Page 46

Edit NetCommand®: Add an A/V Receiver, continued

A/V Receiver (AVR) Input Learn Screen

Figure 10

NetCommand can now learn the remote control signals used to select each input on the A/V receiver.

1.Press ADJUST or on the TV remote to select the check box for each function to be learned.

2.Press ENTER and the function name will begin to flash to confirm the ready-to-learn status.

3.Press the button on the A/V receiver’s remote control that corresponds to the selected function. A check mark will appear and the function name will stop flashing. This confirms the signal learned status.

4.To test the learned command, press ENTER on the TV remote. The A/V receiver will perform the selected function. The A/V receiver needs to be turned on and the IR emitters properly placed for the test to be successful (see page 32 for IR emitter placement).

5.To customize the input names, press ADJUST to move to the Input Name text box and then press ADJUST or and ENTER to select each letter of the name. These names will appear on the Review screen as the A/V receiver’s input names, and should match the names the A/V receiver shows in its own display.

6.To erase the learned input signal, highlight the check box for that input and press CANCEL.

7.Repeat for each connected input.

8.When the input selection signals have been learned and the inputs named, press ADJUST to select Next> and move to the A/V receiver Learn screen.

A/V Receiver (AVR) Learn Screen

Figure 11

1.Press ADJUST or on the TV remote to select the check box for each function to be learned.

2.Press ENTER and the function name will begin to flash to confirm the ready-to-learn status.

3.Press the button on the A/V receiver’s remote control that corresponds to the selected function, A check mark will appear and the function name will stop flashing. This confirms the signal learned status.

4.To test the learned command, press ENTER on the TV remote. The A/V receiver will perform the selected function. The A/V receiver needs to be turned on and the IR emitters properly placed for the test to be successful (see page 32 for IR emitter placement).

5.Repeat for each function to be learned.

6.To erase a learned function, highlight the check box for that function and press CANCEL.

7.When the function signals have been learned, press ADJUST to select Next> and move to the Name screen.

Figure 11. A/V receiver Learn screen

Figure 10. A/V receiver Input Learn screen

IMPORTANT

When learning remote control signals, point the device’s remote at the TV screen

46

Chapter 3. NetCommand Setup and Editing

Image 46
Contents Owner’s Guide While Under Warranty After Warranty TV Guide On Screen Access RequirementsLamp Replacement Stand RequirementFCC Declaration of Conformity Important Safeguards Important Safeguards Contents Mitsubishi DLP Projection Television Limited Warranty Our Thanks Mitsubishi Digital Electronics America, IncRemote Control TV Accessories Special Features Front Control PanelTV Accessories      Special Features Front-Panel Indicator Lights System ResetReset Power/Timer IndicatorStatus Indicator Lamp IndicatorRemote Control OverviewSleep Timer Battery InstallationCare Input 1 IR Emitter NetCommandTV Back Panel Component 1, 2, and 3 InputsCableCARD Slot Hdmi 1DTV Link/IEEE Digital Audio OutputFront-Panel Input Media Card Slots and Front-Panel InputsMedia Card Slots Card CompatibilityUsing the Reset Menu to Reset Demo ModeUsing the System Reset Button Additional InformationPage Connecting Connecting External Devices and NetCommand Setup Stereo and/or digital audio cables AV ReceiverCableCARD Technology Using a CableCARDCableCARD Technology Wall Outlet Cable Connecting a Wall Outlet Cable or Cable BoxStandard Cable Box For antennas with flat twin leads Antenna with a Single LeadAntennas with Separate UHF and VHF Leads For cable or antenna with coaxial leadVCR to an Antenna or Wall Outlet Cable Audio & Video $BCMFConnecting a VCR to a Cable Box Audio & Video VCR to a Cable Box Audio & VideoSatellite Receiver or Other Device with S-Video Receiver Stereo SystemTo connect an analog A/V receiver DVD Player with Component Video DVI DeviceHdtv Cable Box or Satellite Receiver with Component Video Hdmi DeviceComputer with an Hdmi Monitor Output Connecting a Computer with an Hdmi or DVI Monitor OutputComputer with a DVI Monitor Output Connecting the IR Emitter NetCommand An IR emitter cable is included with the TVWhen Connecting Ieee 1394 Devices Connecting Compatible Ieee 1394 DevicesCompatible Ieee 1394 Devices Direct Device-To-Device Style Pin Style vs -Pin Style ConnectorsConnection Styles Hub Connection StyleHelpful Hints Page NetCommand Setup and Editing NetCommand Introduction Welcome To NetCommandUsing the Remote Control with NetCommand NetCommand Pre-Memorized DevicesNetCommand Setup On-Screen Buttons Remote Control Buttons 3D GraphicalSetup Reminder NetCommand Initial SetupNetCommand Information Screen Welcome ScreenDevice Setup Screen Review Screen Finish ScreenReceiver Screen Edit NetCommand Add an A/V ReceiverReceiver Inputs Receiver AVR Input Learn Screen Receiver AVR Learn ScreenName Screen Audio Output to AVR ScreenEdit NetCommand Screen Edit NetCommand Add DevicesAdd Screen Device Screen Device Learn ScreenDevice Advanced Learn Screen Connection for Device ScreenRF Connection for Cable Screen VCR for Recordings ScreenIR Code for Device Screen Change Device Screen Edit NetCommand Change or Delete DevicesDelete Device Screen Ieee 1394 Devices and NetCommand- Controlled Recordings Ieee 1394 Devices and NetCommand Control Name for 1394 Device Screen Adding Ieee 1394 Devices AutomaticallyAdding Ieee 1394 Devices Automatically New 1394 Device ScreenIeee 1394 Device Type Screen Connection ScreenDevice Selection Menu Power On/Off DevicesPIP Device Selection Menu IR Controlled Devices Using the Device Menu Button to Display MenusDevice Menu Moving Through Other CableCARD ScreensGuide and the Device Selection Menu Using the Guide Button to Display ChannelView and MenusGuide Button Guide and the Record To MenuTime-Delayed Recording NetCommand-Controlled RecordingsSetting up Recordings Recording NowRecord List, Peer-to-Peer Connections Direct VCR Recording from an Antenna or Cable Source Using A/V DiscsUsing A/V Discs Copy-Protected MaterialTV Menu Screen Operations Main Menu Memorize Channels Setup MenuLanguage ClockTime Zone Timer On/OffDate Daylight Savings TimeEdit NetCommand MenuRemote Control Transport Buttons Transport MenuRecord Menu Recording SetupTime-Delayed Recording RecordCancel Current Recordings Default Digital Record DeviceSetting Up Analog Recordings with TV Guide On Screen Analog RecordingsPrefer Digital Channel MenuAntenna MemorySignal Strength SQV SuperQuickViewAnalog Captions Digital SettingsCaptions Menu BackgroundColor FontsSize Opacity FontEntry Chip Lock MenuChip Chip Start Time and V-Chip Stop TimePrograms without V-Chip signals Chip Signal InformationContent Categories Chip Lock Menu V-Chip DefinitionsLock By Time Front Button LockAudio/Video Menu Analog-Only Audio Settings Setting Descriptions AudioAnalog and Digital Audio Settings Digital-Only Audio SettingsSetting Descriptions Video Video SettingsVertPosition Vertical Position Auto PositionHorizPosition Horizontal Position Fine DetailAdditional Features MediaCommand and Media Card PlaybackOperation of PIP DVD Definitions Signal and Format DefinitionsTV Display Formats Anamorphic or Enhanced for Wide-Screen TV’s57%JTQMBZ PC resolution XGA selection PC ViewingSignal Format Standard Zoom Signal Format 16 X 9 StandardPC Display Formats Don’t pull the media card out while it is playing MediaCommand and Media Card PlaybackInserting a media card For MP3 or WMA Audio PlaybackMedia Command and Media Card Playback Troubleshooting Troubleshooting Problem Possible SolutionThere is a large black or gray rectangle on Devices are grayed out in the Device Selection All Ieee 1394 devices disappear Troubleshooting Appendix G Cleaning and Service Appendix H Lamp Cartridge ReplacementAppendix B Specifications Appendix a Bypassing the V-Chip LockPage Bypassing the V-Chip Lock Appendix a Bypassing the V-Chip LockBypassing Front Button Lock This page intentionally blank TV Specifications Appendix B SpecificationsInputs Outputs Appendix C Remote Control Programming Codes Programming the Remote to Control NetCommand A/V ProductsDVD Players VCR position TV positionCable/SAT/DTV position DVD positionAppendix D Device Control with NetCommand NetCommand Compatible Traditional Devices AnalogWhen an Ieee 1394 Device is Viewed or Played Ieee 1394 DevicesAppendix E NetCommand Specialized Device Keys Digital Program Appendix F On-Screen Information DisplaysAnalog Program Digital Ieee 1394 DeviceAppendix G Cleaning and Service Appendix H Lamp Cartridge Replacement Lamp LifeBurn Danger Do not touch the glass parts of the lamp cartridgeTrademark and License Information Mitsubishi TV Software Index VCR Mitsubishi DLP Projection Television Limited Warranty 115This Limited Warranty does not Cover 116Page MDEAservice@mdea.com Website Mail
Related manuals
Manual 86 pages 7.9 Kb