Mitsubishi Electronics WS-55615A, WS-65515A, WS-65615A VCR to Antenna or Wall Outlet Cable, Red

Page 17

Connecting VCR Video and Audio to an Antenna or Wall Outlet Cable

VCR to Antenna or Wall Outlet Cable

Figure 5

A two-way RF splitter, 3 coaxial cables, right and left audio cables and S-Video or Video cables are required. These are not included with the TV.

1.Connect the incoming cable or Antenna to IN on the RF splitter.

2.Connect one coaxial cable from OUT on the RF splitter to ANTENNA IN on the VCR back panel.

3.Connect one coaxial cable from OUT on the RF splitter to ANT-1 MAIN on the TV back panel.

4.To use the TV speakers with the VCR, connect a set of audio cables from AUDIO OUT on the VCR back panel to INPUT 1 AUDIO-LEFT (MONO) and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel. If your VCR is mono (non-stereo), connect only the white (left) cable.

5.Connect either an S-Video or Video cable from VIDEO OUT on the VCR back panel to INPUT 1 VIDEO on the TV back panel. Only one type of video cable should be connected. S-Video is recommended, if available.

6.For NetCommand® controlled recordings, connect a Video cable from VIDEO IN on the VCR back panel to MONITOR OUTPUT AUDIO/VIDEO 1 on the TV back panel.

7.Complete the NetCommand controlled recording connection by connecting a set of audio cables from AUDIO IN on the VCR back panel to MONITOR OUTPUT AUDIO/VIDEO 1 AUDIO-LEFT (MONO) and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

 

Attach

 

 

only

 

 

one

 

 

cable

S-Video

 

type

 

recommended

 

 

 

 

if available

 

 

5.

 

 

White

2.

 

4. Red

TV back panel

INPUT

 

MONITOR OUTPUT

 

1

 

2

AUDIO/VIDEO 1

AUDIO 2

 

S-VIDEO

 

 

6.

VIDEO

 

AUDIO-

White

(MONO)

LEFT/

 

AUDIO-

Red

RIGHT

2.

VCR back panel

IN

SPLITTER

OUT

 

WAY

 

COMPONENT

7.

HS-U748

4. Red

Incoming Cable 1.

TWO

OUT

 

3.

YPbPr (480i/480p/1080i)

1 2

TUBE

R

Y

Pb

Pr

White

 

 

5.

6.

7.

 

 

3.

DVI

 

 

 

Analog Audio

 

 

 

Digital Video

 

 

 

Digital Audio

 

ANT-2

ANT-1

 

 

AUX

MAIN

 

SERVICE

IEEE1394

DIGITAL

 

PORT

INPUT/OUTPUT

AUDIO

 

 

 

CableCARD

SLOT

 

– (DTV/CABLE /VHF/UHF) –

 

AUDIO-

LEFT/

(MONO)

AUDIO- RIGHT

If your VCR has a video channel

5.

 

 

or RF ON/OFF switch, set it to OFF.

 

 

 

 

 

W

R

 

Attach

h

e

 

i

d

 

only

t

 

 

one

e

 

 

cable

 

 

S-Video

type

 

 

recommended

 

 

 

if available

 

 

 

Figure 5. Connecting a VCR to an Antenna or Wall Outlet Cable

Note:NetCommand® will assume your VCR is connected to inputs as shown here. If you use any other inputs for your VCR or add a second VCR, this change must match in the NetCommand system. See Edit NetCommand... pages 35-42for more information.

IMPORTANT

Additional connection cables are not provided with the TV. They are available at most electronic stores.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Projection Television Owner’s Guide Risk of Electric Shock Contents Important Safeguards Important SAFEGUARDS, cont’d Mitsubishi Digital Electronics America, Inc Our ThanksTelevision Overview ChapterSpecial Features TV AccessoriesFront Control Panel POWER/TIMER IndicatorIEEE-1394 Input/Output Back PanelDigital Audio Output CableCARD SlotHdmi or DVI Devices IR Output-NetCommandDVI Analog Audio Component InputsSide bar images Letterbox top/bottom black barsNews and stock-market report bars Shopping channel logos & pricing displaysConnecting Chart Connecting External Devices & NetCommand SetupCable Box compatible with PIP/POP Connecting a Wall Outlet Cable or Cable BoxSeparate UHF and VHF Antennas Single AntennaFor antennas with twin flat lead For antennas with coaxial leadRed VCR to Antenna or Wall Outlet CableVCR to a Cable Box Connecting VCR Video and Audio to a Cable BoxSatellite Receiver or Other Device with S-Video Receiver or Stereo SystemDVI Device Connecting a DVD Player with Component Video or DVI DeviceDVD Player with Component Video External DTV Receiver with Component Video Hdmi DeviceIR Emitter NetCommand Connecting the IR Emitter NetCommandPin Style vs -Pin Style Connecting Ieee 1394 DevicesConnection Styles Ieee 1394 Device Connection StylesDirect Device-To-Device Style Hub Connection StyleCableCARD Technology Using a CableCARDCableCARD Definition and Initial Screen Display Connecting Helpful Hints NetCommand Setup and Editing Device NetCommand Pre-Memorized DevicesFollowing Remote Control Functions OverviewSleep Timer Remote Control FunctionsOperation, Care, Sleep TimerOperation CareNetCommand On-Screen Buttons 3D Graphical Menu System Remote Control ButtonsNetCommand Information Screen NetCommand Initial SetupDevice Setup Screen Welcome ScreenFinish Screen Review ScreenReceiver Inputs Edit NetCommand, Adding an A/V ReceiverReceiver Screen Receiver Learn Screen Receiver Input Learn ScreenMonitor Out to AVR Screen Name ScreenEdit NetCommand Edit NetCommand, Adding DevicesDevice Screen Add ScreenDevice Advanced Learn Screen Device Learn ScreenVCR for Recordings Screen Connection for Device ScreenRF Connection for Cable Screen IR Code for Device ScreenDelete Screen Change ScreenDevice Selection Menu Device Menu Using the Device Menu Button to Display MenusIR Controlled Devices/IEEE 1394 Menus CableCARD MenuIeee 1394 Devices and NetCommand Controlled Recordings Adding Ieee 1394 Devices Automatically Adding Ieee 1394 Devices AutomaticallyNew 1394 Device Screen Name for 1394 Device ScreenConnection Screen Ieee 1394 Device Type ScreenDigital Audio Signals Digital Video SignalsDigital Control Signal Ieee 1394 Devices CompatibilityUsing the Guide Button to Display ChannelView and Menus Record To Setup NetCommand Controlled RecordingsTime-Delayed Recording Recording NowRecord List Screen Cancel Current RecordingsDisc Search Track List ScreenRestrictions for Traditional VCRs Direct VCR RecordingDirect VCR Recording from an Antenna or Cable Source What is a Peer-to-Peer Connection? NetCommand Controlled Peer-to-Peer ConnectionsSetting up a Peer-to-Peer Connection Canceling a Current Peer-to-Peer ConnectionImportant Notes TV Menu Screen Operations Main Menu Choices Setup Menu Advanced Convergence Reset Factory Defaults MenuNetCommand Menu Antenna Menu SQV SuperQuickView Timer On/Off Setting the ClockTime Menu ManualCaptions Menu Captions MenuAnalog Captions Digital CaptionsSize FontsColor Opacity FontChip Chip Lock MenuEntry Chip Start Time and V-Chip Stop TimeTV Ratings Chip Signal InformationContent Categories Front Button Lock Lock By TimeAudioVideo AudioVideo MenuAnalog and Digital Audio Setting Setting DescriptionsAnalog Only Audio Settings Digital Only Audio SettingsContrast Video SettingsChapter Display Formats Format SignalsFormat Definitions DVD DefinitionsOriginal Signal Changing PIP/POP Device Operation of PIP and POPDevice Menu with Net Command Ieee 1394 Devices Digital Bypassing Front Button Lock Appendix a Bypassing the V-Chip LockBypassing the V-Chip Lock This page intentionally blank Component-1 and Component-2 Inputs Input Levels and Timing with Component Video SignalsAppendix B High Definition Input Connection Compatibility Programming the Remote to Control NetCommand A/V Products Appendix CRemote Control Programming CodesDVD Players Appendix C Remote Control Programming CodesReceivers Cable Boxes and Satellite ReceiversMitsubishi A/V Receivers Mitsubishi CD Players Not all functions for all modelsAppendix D On Screen Information Displays Checkbox Name Appendix E NetCommand Specialized Device KeysAppendix F Cleaning and Service For the WS-48515 Appendix G Diamond Shield Removal for ModelsFor the WS-55515, WS-65515 and WS-65515A For additional assistance, call 800For the WS-55615, WS-55615A, WS-65615 and WS-65615A Appendix G, Diamond Shield Installation for Model WS-73615 WS-65515, WS-65515A, WS-65615, WS-65615A, WS-73615 Appendix H Cabinet Separation for ModelsProblem Possible Solution TroubleshootingTroubleshooting Troubleshooting Using The System Reset Button Additional Information Demo ModeIndex Menu 56 Mitsubishi Projection Television Limited Warranty Mitsubishi Projection TV Limited WarrantyMitsubishi TV Software Page Mitsubishi Digital Electronics America, Inc D405A10

WS-48515, WS-55615A, WS-55615, WS-73615, WS-65515A specifications

The Mitsubishi Electronics WS series of rear-projection televisions, specifically models WS-65615, WS-65515, WS-65615A, WS-55515, and WS-65515A, represent a significant era in home entertainment technology. Known for their innovative features and exceptional image quality, these models were well-regarded for both functional performance and design.

One of the most notable characteristics of the WS series is their use of DLP (Digital Light Processing) technology. This allows for sharper images and more vibrant colors compared to traditional CRT televisions. DLP technology also reduces issues like pixelation, offering a smoother image overall. The WS-65615 and WS-65615A feature a large 65-inch screen, delivering an immersive viewing experience perfect for movie nights and gaming. Meanwhile, the WS-65515 and WS-65515A provide a slightly smaller 55-inch display, which still offers remarkable visuals without taking up as much space.

All models are equipped with a High-Definition Multimedia Interface (HDMI) input, ensuring compatibility with modern devices like Blu-ray players, gaming consoles, and streaming devices. This connectivity is crucial for those looking to enhance their entertainment systems with the latest technology. Additionally, the WS series supports various audio-video formats, giving users flexibility in how they enjoy their content.

Another key feature is the incorporation of a 3D-ready capability, making these TVs future-proof for a time when 3D content was gaining traction. This aspect attracted cinema enthusiasts who wanted to bring an enhanced experience home. The models also include a built-in digital tuner, allowing users to access over-the-air broadcasts without needing an external box.

The WS-65615 and WS-65515 models additionally boast a stylish and slim design that fits well within modern living spaces, combining aesthetics with functionality. Their lightweight construction allows for easier installation and setup.

Overall, the Mitsubishi Electronics WS-65615, WS-65515, WS-65615A, WS-55515, and WS-65515A televisions deliver a compelling mix of advanced technologies, user-friendly features, and stunning visuals. While they may be considered legacy models today, they still exemplify the quality and innovation Mitsubishi Electronics strived for in enhancing the home viewing experience.
Top Page Image Contents