JVC AV-61S902 manual Appendix a, Cleaning the Filters

Page 58

AV-61S902(E) 1/12/01 4:10 PM Page 58

Appendix A

Cleaning the Filters

The lamp and internal circuits of the AV-61S902 are cooled by a fan which draws in cool air through a pair of intakes. The air intakes are located behind the speaker covers on the front of the television and contain air fil- ters which need periodic cleaning. It is very important the filters be kept clean! If the filters become clogged, cooling air may not reach the lamp or internal circuits. This could cause the lamp or internal circuits to overheat and stop functioning. It is recommended the filters be cleaned at least once every three months. If the television is located in an area where it is exposed to higher levels of dust or other particles in the air, more frequent cleaning may be necessary.

Follow the steps below to clean the filters. To clean the filters you will need a Phillips head screwdriver and a vacuum with a hose attachment. Please read all the steps before you begin.

1) Turn the television off.

Press the Power button on the remote control or television’s front panel to turn the television off. Wait until the picture has closed and the 10 LED lights on the front panel have stopped blinking.

2) Unplug the television.

Disconnect the television’s power cord from the AC outlet. Make sure the 10 LED lights have stopped blinking before you unplug the television.

1. Pull

2. Lift

Speaker

Panel

3) Remove the speaker panels.

The next step is to remove the speaker panels located at the bottom of the front of the television cabinet. The top of the speaker panels are held with Velcro. Make sure the television is unplugged (see steps 1 and 2) before removing the speaker panels.

To remove the panels - Grab the panel from the side near the top. Gently pull the top away from the television. When the top part of the speaker panel is fully away from the television, lift up. The panel will come away from the bottom of the television. Set the panel aside. Repeat this step for the other panel.

4) Remove the filter cover.

Each air filter is covered by a filter cover. To remove this filter cover you will need a Phillips head screwdriver. First loosen the screws located at the four corners of the filter cover. Once the screws have been loosened, gently push the filter cover up until the large holes are aligned with the screw heads, then pull away from the television and set aside. Repeat this step for the other filter cover.

Screws

Filter Cover

58

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Projection Television Users Guide Important Safety Precautions USE Order to be able to use the television for a long time Clean the air filter once every three monthsWelcome Do not block the ventilation holesILA element characteristics Television requires a lot of electric powerDo not turn the power on and off repeatedly in a short time Lamp is a consumable itemTable of Contents Button Functions TroubleshootingAppendices Introduction Check the accessories Check that nothing is missingPrepare the remote control Connect the antennaWatching television Adjusting the volumeCancelling the shutting off Choosing a channelConnections Connections ChecklistKnow your jacks and plugs most are color coded Front Panel Diagram Rear Panel DiagramDiagram #1 Cable box Cable and VCR ConnectionsVideo Connection Diagram #3 Blue DTV Decoder ConnectionRed DTV decoder DVD Player Connection AV Compu-Link Front Panel Inputs Home Theater Install the Batteries Remote ControlRemote Control Basics Cable Box or Satellite setup Remote ProgrammingVCR setup MGADVD setup JVCVCR Search Codes Function Search CodesCable/Satellite Search Codes Function DVD Player Search Codes FunctionOnscreen Menus Onscreen Menu SystemUsing the Onscreen Menus Plug In Menu Plug In MenuAuto Tuner Setup StartFinish Initial Setup Menu Initial SetupAntenna INPUT-A INPUT-B Channel Summary Channel Guard MessageMpaa Motion Picture Assoc. of America Ratings ChipChip Special Note about RatingsSet Ratings Guidelines To Set TV Ratings LevelsUnrated Programs Set Lock CodeLanguage Initial SetupFRE SPA DSD OFF Vertical PositionDIGITAL-IN Size Tint Picture AdjustPicture Adjust ColorBright PictureDetail YNR DNR OFFNoise Muting OFF SET Video StatusBass Sound AdjustSound Adjust TrebleSome Sound Advice SAP MonoMID LOW TV Speaker OFFSound Mode Audio SettingsDolby Pro Logic Order to enjoy Dolby Surround sound Enjoy Dolby Surround soundPro Logic 3D-Phonic Other Sound ModesCLOCK/TIMERS Setting the ON/OFF TimerAspect AspectFreeze Button FunctionsSplit SwapMenu Sleep TimerSleep Timer Message ExitVideo Status SoundMuting Natural Cinema100+ Button Number Buttons 10 Key PadReturn+ Menu on TV’s front panel InputLight VCR Buttons TV/CATV SwitchVCR/DVD Switch DVD ButtonsTroubleshooting Problems CheckTroubleshooting Cleaning the Filters Appendix aReinstall the speaker covers Cleaning the filterReinstall the filter cover Caring for the CabinetChanging the Lamp Replacement Lamp KitAppendix B Replacing the LampRemove the left speaker panel Removing the filter unitReinstall the speaker panel Install the new lamp unitRemoving the lamp unit Filter not properly reinstalled Recycling InformationStarting Up Appendix CLED Display Shutting DownLimited Warranty Parts 1 Year Labor 1 Year LampAccessories For service in Canada Authorized Service CentersDon’t service the television yourself Toll Free 1 800Specifications ModelJVC Company of America JVC CANADA, INC
Top Page Image Contents