JVC AV-61S902 Removing the lamp unit, Install the new lamp unit, Reinstall the speaker panel

Page 62
Hex wrench
Light-source lamp unit

AV-61S902(E) 1/12/01 4:16 PM Page 62

Appendix B

Replacing the Lamp - continued

Please read these instructions fully before attempting to replace the lamp. Please observe all safety warnings.

 

6) Removing the lamp unit.

Handle

Using the hex wrench included with the replacement lamp, loosen the

 

two hex screws fastening the lamp unit. Remove the screws and set

 

aside. When the screws have been removed, remove the lamp by grab-

 

bing the handle and sliding the unit towards you.

7) Install the new lamp unit

Slide the new lamp unit into the television by holding the handle

attached to the unit. When the new lamp unit is securely installed inside the television, replace the hex screws using the hex wrench. To ensure the new lamp unit sits properly inside the television, secure the right

hex screw first, then the left. If the lamp unit does not sit securely inside the television, the television will not turn on.

WARNING!

Remember, it is very important you DO NOT TOUCH THE GLASS SURFACE OF THE NEW LAMP. Please re-read the warnings on page 61 regarding the new lamp unit.

Replace the lamp with part number PK-CL200U only! The television is designed to work specifically with this lamp. Lamps other than the PK-CL200U unit may cause malfunctions and/or damage to the television.

The lamp assembly in this product contains mercury. Disposal of the lamp assembly may be regulated due to environmental considerations. For information on replacement, disposal or recycling procedures, please contact JVC Customer Relations at 1-800-252-5722.

THE USED LAMP MUST BE RECYCLED. See page 63 for recycling instructions. To purchase a replacement kit, please call 1-800-882-2345.

8) Install the filter unit.

Position the filter unit back into its place, being careful not to touch the surface of the filter. Position the three screws and tighten using an correct-sized coin.

9) Reinstall the filter cover.

Place the filter cover over the filter. Insert the four screws and tighten them using the screwdriver.

10) Reinstall the speaker panel.

Replace the bottom of the speaker panel first. Insert the two pegs located at the bottom of the panel into the holes at the bottom lip of the television cabinet. When the pegs are in place, gently press the top part of the speaker panel against the television to reinstall. Once the speaker panel is back in place you may plug the television back into the AC power supply and return to normal television viewing.

If you have read the installation instructions and do not feel comfortable changing the lamp yourself, please call for a service technician.

62

Image 62
Contents Projection Television Users Guide Important Safety Precautions USE Order to be able to use the television for a long time Clean the air filter once every three monthsWelcome Do not block the ventilation holesILA element characteristics Television requires a lot of electric powerDo not turn the power on and off repeatedly in a short time Lamp is a consumable itemTable of Contents Appendices TroubleshootingButton Functions Introduction Check the accessories Check that nothing is missingPrepare the remote control Connect the antennaWatching television Adjusting the volumeCancelling the shutting off Choosing a channelKnow your jacks and plugs most are color coded Connections ChecklistConnections Front Panel Diagram Rear Panel DiagramDiagram #1 Cable box Cable and VCR ConnectionsVideo Connection Diagram #3 Red DTV Decoder ConnectionBlue DTV decoder DVD Player Connection AV Compu-Link Front Panel Inputs Home Theater Remote Control Basics Remote ControlInstall the Batteries Cable Box or Satellite setup Remote ProgrammingVCR setup MGADVD setup JVCVCR Search Codes Function Search CodesCable/Satellite Search Codes Function DVD Player Search Codes FunctionOnscreen Menus Onscreen Menu SystemUsing the Onscreen Menus Plug In Menu Plug In MenuAuto Tuner Setup StartFinish Antenna INPUT-A INPUT-B Initial SetupInitial Setup Menu Channel Summary Channel Guard MessageMpaa Motion Picture Assoc. of America Ratings ChipChip Special Note about RatingsSet Ratings Guidelines To Set TV Ratings LevelsUnrated Programs Set Lock CodeFRE SPA Initial SetupLanguage DIGITAL-IN Size Vertical PositionDSD OFF Tint Picture AdjustPicture Adjust ColorDetail PictureBright YNR DNR OFFNoise Muting OFF SET Video StatusBass Sound AdjustSound Adjust TrebleSome Sound Advice SAP MonoMID LOW TV Speaker OFFDolby Pro Logic Audio SettingsSound Mode Order to enjoy Dolby Surround sound Enjoy Dolby Surround soundPro Logic 3D-Phonic Other Sound ModesCLOCK/TIMERS Setting the ON/OFF TimerAspect AspectFreeze Button FunctionsSplit SwapMenu Sleep TimerSleep Timer Message ExitVideo Status SoundMuting Natural CinemaReturn+ Number Buttons 10 Key Pad100+ Button Light InputMenu on TV’s front panel VCR Buttons TV/CATV SwitchVCR/DVD Switch DVD ButtonsTroubleshooting Problems CheckTroubleshooting Cleaning the Filters Appendix aReinstall the speaker covers Cleaning the filterReinstall the filter cover Caring for the CabinetChanging the Lamp Replacement Lamp KitAppendix B Replacing the LampRemove the left speaker panel Removing the filter unitRemoving the lamp unit Install the new lamp unitReinstall the speaker panel Filter not properly reinstalled Recycling InformationStarting Up Appendix CLED Display Shutting DownLimited Warranty Parts 1 Year Labor 1 Year LampAccessories For service in Canada Authorized Service CentersDon’t service the television yourself Toll Free 1 800Specifications ModelJVC Company of America JVC CANADA, INC