BenQ MP620p user manual Connecting Video source devices, Best video quality

Page 23

Connecting Video source devices

You can connect your projector to various Video source devices that provide any one of the following output sockets:

•Component Video

•S-Video

•Video (composite)

You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the Video source device as described below:

Best video quality

The best available video connection method is Component Video (not to be confused with composite Video). Digital TV tuner and DVD players output Component Video natively, so if available on your devices, this should be your connection method of choice in preference to (composite) Video.

See "Connecting a Component Video source device" on page 18 for how to connect the projector to a component video device.

Better video quality

The S-Video method provides a better quality analog video than standard composite Video. If you have both composite Video and S-Video output terminals on your Video source device, you should elect to use the S-Video option.

See "Connecting an S-Video source device" on page 19 for how to connect the projector to an S-Video device.

Least video quality

Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from your projector, being the least video quality of the available methods described here.

See "Connecting a composite Video source device" on page 20 for how to connect the projector to a composite Video device.

Connecting Audio

The projector has a built-in mono speaker which is designed to provide basic audio functionality accompanying data presentations for business purposes only. It is not designed for, nor intended for stereo audio reproduction use as might be expected in home theatre or home cinema applications. Any stereo audio input (if provided), is mixed into a common mono audio output through the projector speaker.

If you have a separate sound system, you will most likely want to connect the audio output of your Video source device to that sound system, instead of to the mono audio projector.

The audio connections illustrated in the following sections are provided for informational purposes only. You need not connect audio to the projector if there is an alternate sound system available, or if audio is not required.

Connection 17

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Welcome Disclaimer CopyrightTable of contents Supported timing for Component-YPbPr input Iv Table of contentsRegulation Statements Table of contentsMemo Vi Table of contents Important safety instructions Important safety instructionsRefer servicing to qualified service personnel But could fail if power cuts or surgesSafety Instructions Bedding or any other soft surface Safety Instructions Introduction Projector featuresIntroduction Shipping contents Lower side Projector exterior viewFront / upper side Rear sideTurns the projector on or off Controls and functionsExternal control panel Mation5Up, 6 Down 3Left, Right4 Remote controlAdjusts the focus of the projected image FreezePush the holder into the remote control Remote control effective rangeReplacing the remote control battery Pull out the battery holderChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector 1500 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1219Connection Connecting a computer or monitorConnecting a computer Connecting a monitor Best video quality Connecting Video source devices1080i 50/ 60 Hz Connecting a Component Video source deviceDevice Video cable Audio cables Connecting an S-Video source deviceConnecting a composite Video source device Start up Utilizing the password functionTo set a password OperationPassword set-up and return to the on-screen menu If you forget the passwordTo enter the password recall procedure To change the passwordFine-tuning the image size and clarity Adjusting the heightAuto-adjusting the image For example Correcting keystoneHiding the image Selecting an application modeSwitching input signal Freezing the image Power indicator light flashesDisconnect the power cord from the wall socket Remote paging operationsMenu system Menu operationKeystone Using the menusPicture menu Picture menu Brightness Color TempDepends on SelectedPro-Picture menu Setting menu Advance menu Economic Mode offHigh Altitude Auto Off offSource ResolutionMode Equivalent Information menuCare of the projector MaintenanceMessage Status Lamp informationCalculation of lamp hour Replacing the lamp Page Restart the projector Temperature informationResetting the lamp counter Tighten the screw that secures the lampProjector is under normal operation IndicatorsLight Status & Description Power Temp Lamp Power events Light Status & Description Power Temp Lamp Lamp eventsFor assistance Light Status & Description Power Temp Lamp Thermal eventsMaintenance Cause Remedy TroubleshootingPlug the power cord into the AC inlet on Make sure that it is switched onProjector specifications SpecificationsSupported timing for Video and S-Video inputs Timing chartSupported timing for PC input Supported timing for Component-YPbPrinputUnit mm Specifications DimensionsWarranty WarrantyLimited Warranty MIC statement Regulation StatementsFCC statement EEC statement
Top Page Image Contents