BenQ MP620p user manual Connecting an S-Video source device, Device Video cable Audio cables

Page 25

Connecting an S-Video source device

Examine your Video source device to determine if it has an unused S-Video output socket available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device:

1.Take the (optional accessory) S-Video cable and connect one end to the S-Video output socket of the Video source device.

2.Connect the other end of the S-Video cable to the S-VIDEO socket on the projector. The final connection path should be like that shown in the following diagram:

A/V device

S-Video cable

Audio cables

•The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting Audio" on page 17 for details.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

•If you have already made a Component Video connection between the projector and this S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 17 for details.

Connection 19

Image 25

Contents Welcome Disclaimer CopyrightTable of contents Supported timing for Component-YPbPr input Iv Table of contentsRegulation Statements Table of contentsMemo Vi Table of contents Refer servicing to qualified service personnel Important safety instructionsBut could fail if power cuts or surges Important safety instructionsSafety Instructions Bedding or any other soft surface Safety Instructions Introduction Projector featuresIntroduction Shipping contents Front / upper side Projector exterior viewRear side Lower sideExternal control panel Controls and functionsMation Turns the projector on or offAdjusts the focus of the projected image Remote controlFreeze 5Up, 6 Down 3Left, Right4Replacing the remote control battery Remote control effective rangePull out the battery holder Push the holder into the remote controlChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Screen Center of lens Projection distance Maximum zoom Minimum zoom1219 1500Connecting a computer Connecting a computer or monitorConnection Connecting a monitor Best video quality Connecting Video source devices1080i 50/ 60 Hz Connecting a Component Video source deviceDevice Video cable Audio cables Connecting an S-Video source deviceConnecting a composite Video source device To set a password Utilizing the password functionOperation Start upTo enter the password recall procedure If you forget the passwordTo change the password Password set-up and return to the on-screen menuAuto-adjusting the image Adjusting the heightFine-tuning the image size and clarity For example Correcting keystoneSwitching input signal Selecting an application modeHiding the image Disconnect the power cord from the wall socket Power indicator light flashesRemote paging operations Freezing the imageMenu system Menu operationPicture menu Using the menusKeystone Picture menu Depends on Color TempSelected BrightnessPro-Picture menu Setting menu Advance menu High Altitude Mode offAuto Off off EconomicMode Equivalent ResolutionInformation menu SourceCare of the projector MaintenanceCalculation of lamp hour Lamp informationMessage Status Replacing the lamp Page Resetting the lamp counter Temperature informationTighten the screw that secures the lamp Restart the projectorLight Status & Description Power Temp Lamp Power events IndicatorsLight Status & Description Power Temp Lamp Lamp events Projector is under normal operationFor assistance Light Status & Description Power Temp Lamp Thermal eventsMaintenance Plug the power cord into the AC inlet on TroubleshootingMake sure that it is switched on Cause RemedyProjector specifications SpecificationsSupported timing for PC input Timing chartSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsUnit mm Specifications DimensionsLimited Warranty WarrantyWarranty FCC statement Regulation StatementsEEC statement MIC statement