BenQ MP620p user manual Lamp information, Calculation of lamp hour, Message Status

Page 43

Lamp information

Calculation of lamp hour

When the projector is in operation, the duration (by hours) of lamp usage is automatically calculated by the built-in timer. The method of calculating the equivalent lamp hour is as follows:

Total (equivalent) lamp hour = 3/4 (hours used in Economic mode) + 1 (hours used in normal mode)

See "Economic Mode (off)" on page 34 for more information on Economic mode.

The lamp hour in Economic mode is calculated as 3/4 of that in normal mode. That is, using the projector in Economic mode helps to extend the lamp hour by 1/3.

Warning message

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

For more detailed information on projector warnings, please refer to "Indicators" on page 41.

The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer.

The following Lamp warning displays will remind you to change the lamp.

Message

Status

The lamp has been in operation for 2800 hours. Install a new lamp for optimal performance. If the projector is normally run with "Economic Mode" selected (See "Economic Mode (off)" on page 34), you may continue to operate the projector until the 2950 hour lamp warning appears.

The lamp has been in operation for 2950 hour. A new lamp should be fitted to avoid the inconvenience when the projector runs out of lamp time.

The lamp has been in operation for over 3000 hours. This message will flash in the center of the screen for about 30 seconds together with the Lamp indicator lighting up red for 40 seconds.

It is strongly recommended that you replace the lamp at this age. The lamp is a consumable item. With the usage time increase, the lamp brightness diminished gradually. This is normal lamp behaviour. You can replace the lamp whenever you notice that the brightness level has significantly diminished. If the lamp is not replaced beforehand, it must be replaced after 3000 hours usage.

Maintenance 37

Image 43
Contents Welcome Disclaimer CopyrightTable of contents Supported timing for Component-YPbPr input Iv Table of contentsRegulation Statements Table of contentsMemo Vi Table of contents Important safety instructions Important safety instructionsRefer servicing to qualified service personnel But could fail if power cuts or surgesSafety Instructions Bedding or any other soft surface Safety Instructions Introduction Projector featuresIntroduction Shipping contents Lower side Projector exterior viewFront / upper side Rear sideTurns the projector on or off Controls and functionsExternal control panel Mation5Up, 6 Down 3Left, Right4 Remote controlAdjusts the focus of the projected image FreezePush the holder into the remote control Remote control effective rangeReplacing the remote control battery Pull out the battery holderChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector 1500 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1219Connecting a computer Connecting a computer or monitorConnection Connecting a monitor Best video quality Connecting Video source devices1080i 50/ 60 Hz Connecting a Component Video source deviceDevice Video cable Audio cables Connecting an S-Video source deviceConnecting a composite Video source device Start up Utilizing the password functionTo set a password OperationPassword set-up and return to the on-screen menu If you forget the passwordTo enter the password recall procedure To change the passwordAuto-adjusting the image Adjusting the heightFine-tuning the image size and clarity For example Correcting keystoneSwitching input signal Selecting an application modeHiding the image Freezing the image Power indicator light flashesDisconnect the power cord from the wall socket Remote paging operationsMenu system Menu operationPicture menu Using the menusKeystone Picture menu Brightness Color TempDepends on SelectedPro-Picture menu Setting menu Advance menu Economic Mode offHigh Altitude Auto Off offSource ResolutionMode Equivalent Information menuCare of the projector MaintenanceCalculation of lamp hour Lamp informationMessage Status Replacing the lamp Page Restart the projector Temperature informationResetting the lamp counter Tighten the screw that secures the lampProjector is under normal operation IndicatorsLight Status & Description Power Temp Lamp Power events Light Status & Description Power Temp Lamp Lamp eventsFor assistance Light Status & Description Power Temp Lamp Thermal eventsMaintenance Cause Remedy TroubleshootingPlug the power cord into the AC inlet on Make sure that it is switched onProjector specifications SpecificationsSupported timing for Video and S-Video inputs Timing chartSupported timing for PC input Supported timing for Component-YPbPrinputUnit mm Specifications DimensionsLimited Warranty WarrantyWarranty MIC statement Regulation StatementsFCC statement EEC statement