BenQ MP620p user manual Indicators, Light Status & Description Power Temp Lamp Power events

Page 47

Indicators

Illustration

• Blank - : Light OFF									•	O : Orange light
									•	R : Red light
•						: Light flashing
•						: Light flashing
•						: Light ON			•	G : Green light




Light								Status & Description

Power			Temp				Lamp

Power events

		Stand-by mode.
O	-	-

The Power indicator light is flashing during powering up.

G				-	-

		The projector is under normal operation.
G	-	-

1.The projector needs 90 seconds to cool down as it was

abnormally shut down without the normal cooling down

O		-	-	process. Or

2.The projector needs to cool for 90 seconds after the power is turned off.

									The projector has shutdown automatically. If you try to re-start
		O					-	- the projector, it will shutdown again. Please contact your dealer
		O					-
									for assistance.
									for assistance.


Light									Status & Description

Power							Temp	Lamp

Lamp events

	-		The projector has shutdown automatically. If you try to re-start
O		R	the projector, it will shutdown again. Please contact your dealer
			for assistance.
-	-		1.	The projector needs 90 seconds to cool down. Or
		R	2.	Please contact your dealer for assistance.

Maintenance 41

Image 47

Contents Welcome Disclaimer CopyrightTable of contents Supported timing for Component-YPbPr input Iv Table of contentsRegulation Statements Table of contentsMemo Vi Table of contents Important safety instructions Important safety instructionsRefer servicing to qualified service personnel But could fail if power cuts or surgesSafety Instructions Bedding or any other soft surface Safety Instructions Introduction Projector featuresIntroduction Shipping contents Lower side Projector exterior viewFront / upper side Rear sideTurns the projector on or off Controls and functionsExternal control panel Mation5Up, 6 Down 3Left, Right4 Remote controlAdjusts the focus of the projected image FreezePush the holder into the remote control Remote control effective rangeReplacing the remote control battery Pull out the battery holderChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector 1500 Maximum zoom Minimum zoomScreen Center of lens Projection distance 1219Connection Connecting a computer or monitorConnecting a computer Connecting a monitor Best video quality Connecting Video source devices1080i 50/ 60 Hz Connecting a Component Video source deviceDevice Video cable Audio cables Connecting an S-Video source deviceConnecting a composite Video source device Start up Utilizing the password functionTo set a password OperationPassword set-up and return to the on-screen menu If you forget the passwordTo enter the password recall procedure To change the passwordFine-tuning the image size and clarity Adjusting the heightAuto-adjusting the image For example Correcting keystoneHiding the image Selecting an application modeSwitching input signal Freezing the image Power indicator light flashesDisconnect the power cord from the wall socket Remote paging operationsMenu system Menu operationKeystone Using the menusPicture menu Picture menu Brightness Color TempDepends on SelectedPro-Picture menu Setting menu Advance menu Economic Mode offHigh Altitude Auto Off offSource ResolutionMode Equivalent Information menuCare of the projector MaintenanceMessage Status Lamp informationCalculation of lamp hour Replacing the lamp Page Restart the projector Temperature informationResetting the lamp counter Tighten the screw that secures the lampProjector is under normal operation IndicatorsLight Status & Description Power Temp Lamp Power events Light Status & Description Power Temp Lamp Lamp eventsFor assistance Light Status & Description Power Temp Lamp Thermal eventsMaintenance Cause Remedy TroubleshootingPlug the power cord into the AC inlet on Make sure that it is switched onProjector specifications SpecificationsSupported timing for Video and S-Video inputs Timing chartSupported timing for PC input Supported timing for Component-YPbPrinputUnit mm Specifications DimensionsWarranty WarrantyLimited Warranty MIC statement Regulation StatementsFCC statement EEC statement