Philips CCC134 Hooking Up the TV/VCR, Hook up your TV/VCR using one of the connections shown

Page 6

6 Hooking Up the TV/VCR

1

Hook up your TV/VCR using one of the connections shown.

A.

Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna

Connect a Cable signal or an antenna to the ANT(enna) Jack.

ANT.

B.

Hooking Up Your TV/VCR With a Cable Box

To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). Then, select channels at the Cable Box.

Connect the Cable signal to the IN Jack on the Cable Box.

Connect an RF coaxial cable (75- ohm, not supplied) to the OUT Jack on the Cable Box and to the ANT(enna) Jack on the TV/VCR.

OUT

ANT.

IN

RF coaxial cable

(not supplied)

C.

Hooking Up Your TV/VCR With an Indoor Antenna

To install a rod antenna (not sup- plied), push the stem of the antenna into the antenna hole on the top of the TV/VCR. Connect the antenna wire to the ANT(enna) Jack on the back of the TV/VCR as shown. Extend the antenna and adjust its length, direction, and angle for the clearest picture.

Rod Antenna

(not supplied)

ANT.

Image 6

Contents Color TV with built-in VCR This bolt of lightning indi- cates uninsulated material Dear Philips product ownerFor Customer Use Model No Serial NoIntroduction FeaturesSafety Precautions Declaration of ConformityTable of Contents Using the Remote Control Putting Batteries in the Remote ControlBattery Safety TV/VCR MaintenanceRF coaxial cable Not supplied Hook up your TV/VCR using one of the connections shownHooking Up the TV/VCR Rod AntennaCrooked Pin Straight Pin Hooking Up the TV/VCR cont’dBent pin Cable PlugTurning On the TV/VCR Press the Menu button. The screen shown below will appearLanguage Selection Press the Combi button, then press the Menu buttonAutomatic Channel Setup Wait for the TV/VCR to set up channelsRepeat steps 3-4 to add or delete other channels Adding/Deleting ChannelsPress the PLAY/o button or the STOP/p button to select Programming of the last channel you selected will appearSetting the Clock Manual Clock SettingCable Box users must set the clock manually Setting the Clock cont’d Setting the Clock cont’d Automatic PBS Channel SelectionWait for the TV/VCR to find TimeNOW Searching flashes on the TV/VCR screen Manual PBS Channel Selection Use the Number buttons to select your PBS station Wait for the TV/VCR to find the timeDaylight-Savings Time Time Zone Find the brand of your Cable Box/DBS on the lists below Setting the Remote to Operate a Cable Box/DBSFind your code Remember the two-digit number beside itTwo-digit code for your Cable Box/DBS. For example, if Repeat . If the remote control works your CableWithin 30 seconds, press the Number buttons to enter You have a Zenith Cable Box, press Number buttons 0Front Panel ANTenna Jack AC Power CordRear Panel Connect your antenna or cable hereRemote Control Buttons Remote Control Buttons cont’d Adjusting the Picture Controls Decrease Increase Decreased brightnessIf you select Status ON, then select Counter only on On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status OFFPlaying Follow the steps below to play a tapeInsert a tape in the TV/VCR Power button to turn on the TV/VCR, if necessary RecordingPress the RECord/OTR button once to start recording One-Touch Recording Press the STOP/EJECT but- ton on the TV/VCR to stop the OTRRerecording Tape Duplication Different brands of equipment may operate differentlyDefeat Recording Follow the steps below to prevent accidental recordingTimer Recording DailyTimer Recording cont’d Timer Recording cont’d Checking or Clearing Timer Recordings Setting Up the VCR Plus+ Programming System TV ChannelsStation Setting Up the VCR Plus+ Programming System cont’d Examine the lists onYou have completed the steps on pages Press the Combi button, then press the VCRPLUS+/ENTER button Timer Recording With the VCR Plus+ Programming System cont’d Real-Time Counter Memory Appear on the screenRepeat Play TV programming will appear while the tape is rewindingB Repeat Play Press the PLAY/ button or the STOP/ button to selectRepeat Play cont’d Super High Speed Searching LP/SLP Playback OptionsForward and Reverse Searching SP/LP/SLP Viewing a Still PictureBlue Background SmartLock SmartLock cont’d Ratings are defined onExample Specific Sub-ratings To change the access code, follow these steps Use the Number buttons to enter your old access codeRating Explanations Sleep Timer Press the Combi button, then press the SLEEP/WAKE UP buttonWake Up Timer Menu Closed CaptionExample ScreenClosed Caption cont’d Standard Closed CaptionsHalf-screen text Volume Bar Volume BarUsually, the volume bar appears when you press the VOLume Automatic Operation Features TV Reset SmartPictureSwitching the Antennas FM RadioReminder ReminderIndex Search Tape in the TV/VCRHelpful Hints Helpful Hints cont’d Glossary Specifications Limited Warranty Please contact Philips at French Speaking English SpeakingModel # Serial # Index Supplied Accessories Supplied Accessories