Philips CCC134 Turning On the TV/VCR, Press the Menu button. The screen shown below will appear

Page 8

8 Turning On the TV/VCR

Before you turn on the TV/VCR, make sure batteries are in the remote control and you have connected the TV/VCR correctly. The instructions on this page work only when you turn on the TV/VCR for the first time.

1

Press the COMBI button, then press the POWER button. The TV/VCR will come on and the screen shown below will appear.

SELECT LANGUAGE

> ENGLISH

ON

ESPAÑOL

SELECT KL OR

PRESS MENU TO CONTINUE

2

Press the PLAY/K button or the STOP/L button to select

English or Spanish on-screen displays and menus.

3

Press the MENU button. The screen shown below will appear.

CONNECT ANTENNA OR CABLE

TO TVCR

THEN PRESS B

TO END PRESS EXIT

4

Press the F.FWD/B button to begin automatic channel setup. The TV/VCR will memorize all available channels. When channels are set, CHANNELS ARE SET will appear on the screen briefly. Then the TV/VCR will go to the lowest available channel. If you try to set up channels when there is no antenna or cable connected to the TV/VCR, programming will appear to take place, but eventually a NO TV SIGNALS ... message will appear on the screen. Connect an antenna or cable to the ANT(enna) jack on the TV/VCR, then press the F.FWD/B button again. You may need to follow the steps on page 10 instead.

5

Use the CH(annel) o/p buttons or the Number buttons on the remote control to select a TV/VCR channel. Use the VOL(ume) o/p buttons to adjust the sound.

When you scan channels with the CH(annel) o/p buttons, only the memorized channels will be available. Use the Number but- tons to select non-memorized channels.

EJECT

3

 

 

POWER

 

1

MENU

STATUS

CLEAR

FM

/EXIT

 

 

 

1

2

 

3

 

5

4

5

 

6

 

7

8

 

9

 

SLEEP/

 

 

ALT.CH

 

WAKE UP

0

 

2

 

REC

 

 

PAUSE

 

/OTR

PLAY

/STILL

 

 

 

 

REW

F.FWD

 

 

STOP

 

4

 

CH.

 

 

VOL.

 

 

MUTE

 

5

1

CABLE

COMBI

 

SMART

 

/DBS

 

PICTURE

 

 

SPEED

MEMORY VCR PLUS+

 

F.ADV

 

SLOW

ENTER

 

 

 

 

 

 

TRACKING

VAR.SLOW

 

 

 

INDEX

 

SKIP

 

 

 

 

SEARCH

 

Helpful Hints

•If you do not see any on-screen dis- plays when you turn on the TV/VCR, check your hookups, then try again. If you still do not see any on-screen displays, follow the steps on pages nine-10 to select a language and set up channels.

•To skip step 2, press the MENU button. All on-screen displays will be in English. To skip step 4, press the STATUS/EXIT button. Automatic Channel setup will not occur, and CHANNELS NOT SET will appear on the screen briefly.

•You cannot set up channels if you are using a Cable Box.

•Line Input mode is channel 00. When you select channel 00, A/V IN will appear on the screen briefly. Press the CH(annel) o/p buttons or the Number buttons to select another channel.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Color TV with built-in VCR Dear Philips product owner For Customer UseThis bolt of lightning indi- cates uninsulated material Model No Serial NoFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Putting Batteries in the Remote Control Battery SafetyUsing the Remote Control TV/VCR MaintenanceHook up your TV/VCR using one of the connections shown Hooking Up the TV/VCRRF coaxial cable Not supplied Rod AntennaHooking Up the TV/VCR cont’d Bent pinCrooked Pin Straight Pin Cable PlugTurning On the TV/VCR Press the Menu button. The screen shown below will appearLanguage Selection Press the Combi button, then press the Menu buttonAutomatic Channel Setup Wait for the TV/VCR to set up channelsAdding/Deleting Channels Press the PLAY/o button or the STOP/p button to selectRepeat steps 3-4 to add or delete other channels Programming of the last channel you selected will appearCable Box users must set the clock manually Setting the ClockManual Clock Setting Setting the Clock cont’d Setting the Clock cont’d Automatic PBS Channel SelectionNOW Searching flashes on the TV/VCR screen Wait for the TV/VCR to findTime Manual PBS Channel Selection Use the Number buttons to select your PBS station Wait for the TV/VCR to find the timeDaylight-Savings Time Time Zone Setting the Remote to Operate a Cable Box/DBS Find your codeFind the brand of your Cable Box/DBS on the lists below Remember the two-digit number beside itRepeat . If the remote control works your Cable Within 30 seconds, press the Number buttons to enterTwo-digit code for your Cable Box/DBS. For example, if You have a Zenith Cable Box, press Number buttons 0Front Panel AC Power Cord Rear PanelANTenna Jack Connect your antenna or cable hereRemote Control Buttons Remote Control Buttons cont’d Adjusting the Picture Controls Decrease Increase Decreased brightnessOn-Screen Status Displays If you select Status ON, then select Counter only OFFIf you select Status ON, then select Counter only on If you select Status OFFInsert a tape in the TV/VCR PlayingFollow the steps below to play a tape Press the RECord/OTR button once to start recording Power button to turn on the TV/VCR, if necessaryRecording One-Touch Recording Press the STOP/EJECT but- ton on the TV/VCR to stop the OTRRerecording Tape Duplication Different brands of equipment may operate differentlyDefeat Recording Follow the steps below to prevent accidental recordingTimer Recording DailyTimer Recording cont’d Timer Recording cont’d Checking or Clearing Timer Recordings Station Setting Up the VCR Plus+ Programming SystemTV Channels Setting Up the VCR Plus+ Programming System cont’d Examine the lists onPLUS+/ENTER button You have completed the steps on pagesPress the Combi button, then press the VCR Timer Recording With the VCR Plus+ Programming System cont’d Real-Time Counter Memory Appear on the screenRepeat Play TV programming will appear while the tape is rewindingB Repeat Play Press the PLAY/ button or the STOP/ button to selectRepeat Play cont’d Playback Options Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureBlue Background SmartLock Example Specific Sub-ratings SmartLock cont’dRatings are defined on To change the access code, follow these steps Use the Number buttons to enter your old access codeRating Explanations Sleep Timer Press the Combi button, then press the SLEEP/WAKE UP buttonWake Up Timer Closed Caption ExampleMenu ScreenHalf-screen text Closed Caption cont’dStandard Closed Captions Usually, the volume bar appears when you press the VOLume Volume BarVolume Bar Automatic Operation Features TV Reset SmartPictureSwitching the Antennas FM RadioReminder ReminderIndex Search Tape in the TV/VCRHelpful Hints Helpful Hints cont’d Glossary Specifications Model # Serial # Limited WarrantyPlease contact Philips at French Speaking English Speaking Index Supplied Accessories Supplied Accessories
Top Page Image Contents