Philips CCC194, CCC134 owner manual FM Radio, Switching the Antennas

Page 59

Follow the steps below to listen to FM radio stations through the TV/VCR.

1

Press the COMBI button, then press the FM button to select FM mode. The radio frequency appears on the TV/VCR screen, moving around the screen every few seconds.

FM 88.0MHz

2

Press the CH(annel) o//p buttons until your desired radio frequency appears. You can choose FM stations within the band range of 88.0 ~ 108.0 MHz. You may get better FM reception by repositioning the TV/VCR.

3

To exit FM mode and return to TV mode, press the FM button again.

Switching the Antennas

If you receive a weak radio signal, you may go to TV mode and switch between the internal (INT) and external (EXT) antennas. When you select the external antenna, make sure your TV antenna or TV cable signal is connected to the ANT(enna) Jack on the TV/VCR. Details are on page six.

To switch the antennas, follow these steps.

1

Press the COMBI button, then press the FM button to return to TV mode if necessary.

2

Press the MENU button.

3

Press the PLAY/▲ button or the STOP/▼ button to select FM ANTENNA.

4

Press the REW(ind)/{ button or the F.FWD/B button to select INT or EXT.

5

Press the STATUS/EXIT button.

FM Radio 59

Choosing FM stations...

	EJECT		POWER		1,3
			POWER
	1	2		3
	MENU	STATUS	CLEAR	FM
	MENU	/EXIT	CLEAR	FM
	4	5		6
	7	8		9
	SLEEP/			ALT.CH
	WAKE UP	0		ALT.CH
		0
	REC			PAUSE
	/OTR	PLAY		/STILL
		PLAY
2	REW		F.FWD
		STOP
	CH.	MUTE		VOL.
	CABLE	COMBI		SMART
	/DBS	COMBI		PICTURE
		SPEED	MEMORY VCR PLUS+
	F.ADV		SLOW	ENTER
	TRACKING		VAR.SLOW
		INDEX		SKIP
			SEARCH

Helpful Hints

•If you turn off the TV/VCR in FM mode, the TV/VCR will be in TV mode when you turn on the TV/VCR again.

•You cannot record the FM station.

•You cannot switch to FM mode dur- ing tape playback, although tape playback is allowed while in FM mode.

•You must be in TV mode in order to select Line Input mode (A/V IN).

Image 59

Contents Color TV with built-in VCR Model No Serial No Dear Philips product ownerFor Customer Use This bolt of lightning indi- cates uninsulated materialDeclaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents TV/VCR Maintenance Putting Batteries in the Remote ControlBattery Safety Using the Remote ControlRod Antenna Hook up your TV/VCR using one of the connections shownHooking Up the TV/VCR RF coaxial cable Not suppliedCable Plug Hooking Up the TV/VCR cont’dBent pin Crooked Pin Straight PinPress the Menu button. The screen shown below will appear Turning On the TV/VCRPress the Combi button, then press the Menu button Language SelectionWait for the TV/VCR to set up channels Automatic Channel SetupProgramming of the last channel you selected will appear Adding/Deleting ChannelsPress the PLAY/o button or the STOP/p button to select Repeat steps 3-4 to add or delete other channelsCable Box users must set the clock manually Setting the ClockManual Clock Setting Setting the Clock cont’d Automatic PBS Channel Selection Setting the Clock cont’dNOW Searching flashes on the TV/VCR screen Wait for the TV/VCR to findTime Manual PBS Channel Selection Wait for the TV/VCR to find the time Use the Number buttons to select your PBS stationDaylight-Savings Time Time Zone Remember the two-digit number beside it Setting the Remote to Operate a Cable Box/DBSFind your code Find the brand of your Cable Box/DBS on the lists belowYou have a Zenith Cable Box, press Number buttons 0 Repeat . If the remote control works your CableWithin 30 seconds, press the Number buttons to enter Two-digit code for your Cable Box/DBS. For example, ifFront Panel Connect your antenna or cable here AC Power CordRear Panel ANTenna JackRemote Control Buttons Remote Control Buttons cont’d Adjusting the Picture Controls Decreased brightness Decrease IncreaseIf you select Status OFF On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status ON, then select Counter only onInsert a tape in the TV/VCR PlayingFollow the steps below to play a tape Press the RECord/OTR button once to start recording Power button to turn on the TV/VCR, if necessaryRecording Press the STOP/EJECT but- ton on the TV/VCR to stop the OTR One-Touch RecordingDifferent brands of equipment may operate differently Rerecording Tape DuplicationFollow the steps below to prevent accidental recording Defeat RecordingDaily Timer RecordingTimer Recording cont’d Timer Recording cont’d Checking or Clearing Timer Recordings Station Setting Up the VCR Plus+ Programming SystemTV Channels Examine the lists on Setting Up the VCR Plus+ Programming System cont’dPLUS+/ENTER button You have completed the steps on pagesPress the Combi button, then press the VCR Timer Recording With the VCR Plus+ Programming System cont’d Appear on the screen Real-Time Counter MemoryTV programming will appear while the tape is rewinding Repeat PlayPress the PLAY/ button or the STOP/ button to select B Repeat PlayRepeat Play cont’d Viewing a Still Picture Playback OptionsForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPBlue Background SmartLock Example Specific Sub-ratings SmartLock cont’dRatings are defined on Use the Number buttons to enter your old access code To change the access code, follow these stepsRating Explanations Press the Combi button, then press the SLEEP/WAKE UP button Sleep TimerWake Up Timer Screen Closed CaptionExample MenuHalf-screen text Closed Caption cont’dStandard Closed Captions Usually, the volume bar appears when you press the VOLume Volume BarVolume Bar Automatic Operation Features SmartPicture TV ResetFM Radio Switching the AntennasReminder ReminderTape in the TV/VCR Index SearchHelpful Hints Helpful Hints cont’d Glossary Specifications Model # Serial # Limited WarrantyPlease contact Philips at French Speaking English Speaking Index Supplied Accessories Supplied Accessories