Philips 58PFL4609 Channel installation, Autoprogram, Weak channel installation, Installation mode

Page 34

Channel installation

Be sure the RF cable is correctly connected to this Unit and you are registered with your Cable TV provider when you Install Cable channels.

Autoprogram

If you switch wires (e.g. between antenna and CATV) or if you move the unit to a different area after the initial setting, or if you restore the DTV channels you deleted, it is recommended to use AutoProgram to perform a new channel search.

You need to select the signal type in Installation mode before you perform AutoProgram.

1Use H I to Select Channels, then press OK.

2Use H I to Select Autoprogram, then press OK.

If you run Autoprogram when you have Locked Channels, a

Message appears asking to enter your PIN. Enter your PIN in order to Complete the Installation. You need to set the Channel Lock again after the Installation.

3 Press OK to Select Start now.

 

When the Scanning and Memorizing of Available Channels is

4

Completed, the Lowest Memorized Channel will be Displayed.

Follow the On-screen Instructions to Complete the Installation.

 

System searching. Please wait...

 

 

Digital channels found:

0

 

Analog channels found:

0

Auto programming may take more than 20 minutes to complete.

Stop

Note(s)

After setting Autoprogram, using CH + / – skips unavailable channels automatically.

If you are not receiving a signal from your Cable service, contact the Cable provider.

If you press B or OK during Autoprogram, the setup of TV channels will be cancelled.

Even if Autoprogram is completed, the channel setting will be lost if the AC power cord is unplugged before the unit goes into Standby mode by pressing B.

The PIN Code will be required Once you set a PIN code in the Child and Ratings Lock. L p. 31

If you want to change your PIN code, follow the instruction for Change PIN. L p. 33

34 .English

Weak channel installation

This function lets you add the channels that were not added by the AutoProgram due to the reception conditions during the initial setup. It is available only when you select Antenna in Installation mode.

1Use H I to Select Channels, then press OK.

2Use H I to select Weak channel installation, then press OK.

The PIN code will be required if you have locked channels. 3 Use J K to select channel Input box, then use H I to select a

channel you want to memorize.

4Use J K to select Search, then press OK.

5Display will be changed to Store from Search when the channel is found, then press OK.

Note(s)

In most cases, Digital channels are not broadcast on the RF channel on which they appear on your TV. To add Digital channels you need to know the RF channel on which the Digital channel is being broadcast. (e.g. If there is a Digital channel 9.1 which is being broadcast on RF channel 25, you need to enter 25 while performing a weak channel installation.) To find out the RF channel on which a particular Digital channel is being broadcast, please contact your local service provider. Installing Digital channels using Weak channel installation might not work for direct cable connections and if the Digital signal is too weak for the TV to process.

Installation mode

1Use H I to Select Channels, then press OK.

2Use H I to select Installation mode, then press OK.

3Use H I to select Antenna or Cable, then press OK.

When Antenna is selected, the TV detects antenna signals. It searches for DTV and Analog TV channels available in your area.

When Cable is selected, the TV detects signals supplied by cable. It searches for DTV Analog TV and Cable channels available in your area.

Uninstall channels

The channels selected here can be skipped when selecting the channels using CH + / –.

Those channels can still be selected with the NUMBER buttons.

1Use H I to Select Channels, then press OK.

2Use H I to select Uninstall channels, then press OK.

3Use H I to select the channel you want to remove, then press OK.

The removed channels are not displayed on the list of favorite channels.

To reactivate a removed channel, use H I then press OK.

Image 34
Contents Register your product and get support at Contents Product Safety Notification Sanus PLA50B Left and right sideBottom M6 x 0.787 20mmTrade Name Responsible Party Model Address Telephone Number PhilipsCinemaNow is supported in 58PFL4909 only Their respective ownersTarget Ticket is supported in 58PFL4909 only Preparing to Move/Ship the Unit Positioning the TV Regulatory NoticesEnvironmental Care PackagingSupplied Accessories FeaturesGetting Started Slide the battery cover off the back of the Remote Control Stand AssemblyInstalling the Remote Control Batteries Attaching the BasePREV.CH Remote ControlTo enter 2.1, press Returns to the previously viewed ChannelTerminals Control PanelVideo Plugging in the AC Power Cord Connecting Antenna or Cable / Satellite / Iptv BoxAudio L/R cables Connecting your Devices Selecting your Connection qualityComponent Analog Video Connection Connecting the TV to the Internet using an Ethernet cableHDMI-ARC Connection Composite Analog Video ConnectionDigital Audio Output Connection Connecting the TV to the Internet using a Wireless LANPC Connection HDMI-DVIXGA USB Memory StickVGA WxgaSkip Initial SetupStop Picture aPersonal Press OK to finish Settings assistantCancel Sound aSwitching Channels Switching on your TV and putting it in Standby modeAdjusting Volume Use your TVWatching Channels from an External Device Access the Home menuEnable or disable RC key forwarding from the Home menu Guide to Home menuCreate and use lists of favorite channels Using auto modeSwitch to one of the channels on a list Select a list of favorite channelsChanging Picture Format MPEG4 TV Screen informationMPEG1 YESPicture Jpeg Music MP3Video When the Setting is completed, press Q Menu or Back to exit Making more use with your TVPicture Backlight SoundContrast Features Brightness Settings assistant Start nowSharpness Advanced settings Hdtv Auto sound Personal Auto volume leveling OffTV speakers Headphone volume Digital output format Equalizer Start now Sound BalanceCaption settings Sleep timer Child and Ratings LockTV ratings lock Setting TV and movie ratingsChannel lock Child lock Movie ratings lockLanguage Change PINCanadian English or Canadian French Ratings Installation mode Channel installationWeak channel installation Uninstall channelsPreferences Setting your location to homeTV placement Use Philips EasyLinkMaster EasyLink Auto TV On EasyLink Hdmi CECDevice List RC key forwarding SelectNetwork settings assistant NetworkManual network settings WPA/WPA2 Proxy configuration Setting statusConnection test Checking your current software version Return your settings to default valuesReset network settings Home networkAn empty clean formatted USB Memory Stick Preparing for the software upgradeUSB upgrade Upgrading the softwareNetflix ESN Automatically check for latest softwareNetflix deactivation Vudu deactivationUsing Philips Wirelessconnect Philips WirelessconnectInstall Philips Wirelessconnect 1GB RAMUsing Dlna View photos, play music and watch videos using DlnaBefore using Dlna Guide to DlnaListen to music using Dlna View your pictures using DlnaWatch videos using Dlna Net TV Adding Pandora User Accounts PandoraN operationsActivating Pandora Creating a New StationUseful tips Question AnswerTroubleshooting Unusual picture appears and the TV does Not operateWireless LAN connection fails or wireless connection is poor Information MaintenanceGlossary VHF SpecificationsUHF Warranty Shipping charges to return defective product to PhilipsLicense A4D52UH / A4D5AUH