Philips DVD741VR owner manual You can not insert a video cassette, You can not remove the tape

Page 77

H9231CD(EN).QX3 02.9.5 7:14 PM Page 77

Helpful Hints (cont’d) 77

You can not insert a video cassette.

•Insert the tape, window side up, with the record tab facing you.

•

Make sure a tape isn’t already in the VCR by pressing STOP/EJECT on the front of the DVD/VCR.

•

Gently push on the center of the tape when putting it in the VCR. Never force the tape into the VCR.

•If a timer recording is set, you cannot insert a tape without a record tab.

You can not remove the tape.

•The DVD/VCR must be in VCR mode. Press OUTPUT SELECT so the green VIDEO light is on the front of the DVD/VCR.

•Make sure the power plug is completely connected to a power outlet.

•You have set a timer recording. Press TIMER SET to delay the timer recording.Then, press STOP/EJECT on the front of the DVD/VCR to eject the tape. Insert another tape and press TIMER SET to reset the timer recording.

•Unplug the DVD/VCR power cord for five minutes.Then, plug in the power cord again, then press POWER ON/OFF on the DVD/VCR. If the tape does not eject, press STOP/EJECT on the DVD/VCR three to five times. If the tape still does not eject, you may need to have an authorized servicer remove the tape.

DVD/VCR ejects the tape when you press REC/OTR or TIMER SET for a timer recording.

•Make sure the tape has a record tab. Details are on page 31.

Direct Broadcast System Hookups

•Watching one TV channel while recording another may not be possible if you have a DBS hookup.You

may have to set your TV to channel 03 or 04, then make your channel selections at the DBS.

•With many DBS hookups, if you use accessory audio and video cables to connect your DVD/VCR to your TV, you will have to put your DVD/VCR in Line Input mode (channel 001 or 002).

Line Input mode

•If you accidentally enter Line Input mode (AV FRONT or AV REAR will appear on your TV screen briefly), press CHANNEL/SKIP j/i (p/o) or the Number buttons to select another channel.

Hi-Fi Stereo Sound

•During playback, Hi-Fi audio may normally revert to normal audio when you adjust tracking.

•When connecting the DVD/VCR to a stereo TV, you will only get stereo sound if you use audio cables to connect the DVD/VCR AUDIO OUT jacks on the DVD/VCR to the AUDIO IN jacks on your TV, and if the TV is in Line (Auxiliary) Input mode. See your TV owner’s manual for details.

•When you connect the DVD/VCR AUDIO OUT jacks on the DVD/VCR to the AUDIO IN jacks on your TV, the stereo light on the TV might not glow. If the status display indicates you are receiving stereo, you are. Details are on page 44.

•Only tapes recorded in Hi-Fi audio will play in Hi-Fi audio.Tapes recorded in normal audio will play in monaural audio.

Cleaning the Video Heads

•Your DVD/VCR automatically cleans the video heads of the VCR each time you insert a tape. However, the heads may become dirty. If so, have an authorized servicer clean the video heads. Eventually, the heads may need to be replaced.

The playback picture is too dim, too bright, or fluctuates in brightness.

•Some programs may be broadcast with copyright protection technology in order to protect the rights of copyright owners.This technology is used on programs that are recorded on video cassettes or DVDs, as well as some programs broadcast by antenna/cable/satellite television channels. Programs broadcast with copyright protection may not record clearly. Likewise, if you play a tape that is a recording of a copyright protected program, the picture may not be clear.Tapes of copyright protected programs may have a pic- ture that is dark or dim, or the brightness of the picture may fluctuate.Therefore, avoid recording or play- ing copies of copyright protected programs.

•This DVD/VCR incorporates copyright protection technology that is protected by method claims of cer- tain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Channels above 13 cannot be received.

• Select CABLE TV at the TUNER SET UP menu (page 24), then let the DVD/VCR set up the channels.

Page 76 Page 78
Image 77
Page 76 Page 78
Contents Digital Video Disc Player Video Cassette Recorder For Customer Use Dear Philips product ownerDeclaration of Conformity Safety and General InformationSafety Precautions Table of Contents Introduction Playable Discs and Video Cassettes Determining the best possible connection HookupsBefore you begin RememberANT-IN Antenna In Jack of your DVD/VCR Hookups cont’d2DVD/VCR ConnectionsTV’s Antenna Signal CableCable On TV Video Cable 2Audio Cables Back of Stereo example only Stereo Receiver Putting Batteries in the Remote Control Remote Control SetupUsing the Remote Control Recycling Guidelines/Battery SafetyTurn on the TV First-time DVD/VCR SetupWithin 60 seconds, press Play B o or Stop C Guage for VCR on-screen displays and menusRead and follow the steps below to play a tape Video Cassette PlaybackTurn on the TV and set it to channel 3 or 4, whichev Turn on the TV. Insert a tapePress OPEN/CLOSE on the DVD/VCR 4Insert a Disc Disc PlaybackDisplay Panel DVD Power Light This light appears when the power is onDisplay Messages Display with Dimmer DVD Light redDisplay Panel VCR Front Panel CH3/CH4 Switch DVD/VCR Audio OUT Jacks AC Power CordANT-IN Antenna In Jack Cb Cr JacksRemote Control Buttons Remote Control Buttons cont’d 22-4 Channel SetupPress VCR, then press DISC/MENU Channel Setup cont’dAdding/Deleting Channels Reviewing Memorized Channels SET UP, then press FF g BPress Play B o or Stop C p to select Tuner Press DISPLAY/STATUS/EXIT once or twice to exitClock VCR Power failures can erase the clock settingSet the clock. Details are on Daylight-Savings TimeMenu Language Selection VCRIf you select Status on and Counter only on VCR On-Screen Status DisplaysIf you select Status on and Counter only OFF If you select Status OFFVideo Cassette Tape Recording DVD/VCR will record in a preset volumeRecording Prevention Turn on the TV Insert a tape in the DVD/VCRSelect the channel you Want to watch at the TV Recording One Channel/Watching AnotherTo stop an OTR before recording is finished, press Stop C p One-Touch RecordingTo record the programs Timer RecordingFront of the DVD/VCR DVD/VCRPress two Number buttons for the hour you want Timer Recording cont’dRecording to begin. Press two Number buttons For the minute you want the recording to beginTape Speeds Press the Number 1 button to record in SP speedOr the Number 2 button to record in SLP speed See page 76 for more hints Checking or Cancelling Timer RecordingsMake the connections shown above Rerecording Tape DuplicationCassette compartment of DVD/VCR 2. Turn on the TV and set it to channel 03 orRepeat Play To cancel Repeat Play, follow stepsPress Play B o or Stop C p to select Press FF g B so on appears beside RepeatWhile the status display is on the screen, press Clear to reset the real-time tape counter to zeroReal-Time Tape Counter Memory Press VCR, then press Search MODE/TIME Time SearchForward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Understanding On-Screen Displays Multi-Channel Television SoundOn will appear to the right of your selection SET UP, then press FF gBMulti-Channel Television Sound cont’d Please see additional notes on Hi-Fi Stereo SoundLight appears on the front of the DVD/VCR Blue BackgroundUsing the Title Menu Using the DVD Disc MenusDisc Menus Press DVD, then press TITLE. The Title Menu willBack speed Fast Forward/Reverse SearchAn h x2, h x8, h x30, or h x60 will appear Press Play B o to return to normal playbackSpecific Title/Chapter Playback Specific Title/Chapter Playback, Specific Time PlaybackSpecific Time Playback Title/Chapter playback is not avail- able with some DVDsSpecific Track Playback BA-BResuming playback Paused and Step-by-Step Playback, Resuming PlaybackPaused and Step-by-Step Playback Repeat,A-B Repeat Press Repeat until the repeat mode you wantRepeat During disc playback, press DVD, then repeatedlyMarkers When the Disc reaches the point you want toPress DVD, then press MARKER. The Markers will Let the Disc continue to play to the point at whichSubtitles, Camera Angles Opening the disc tray will cancel your subtitle settingSubtitles Camera AnglesPress Setup to remove the menu Parental Controls PasswordWrite down your password in case you forget it Press the Number buttons to enter your four-digitWhile playback is stopped, press DVD, then press Parental Controls LevelsPress the Number 4 button to select Parental Press the Number 1 button to select Parental LevelAppears on the front of the DVD/VCR Audio LanguageYou can select a language for DVDs during playback.You can Slow Motion Slow Motion, ZoomZoom Press DVD, then press Zoom during playbackMODE. The Program screen will appear Programmed PlaybackIf you enter a wrong Track number, press CLEAR.The last Number button for the first digit, then the Number butStereo Sound Mode Random Playback, Stereo Sound ModeRandom Playback Press Audio repeatedly during playback to chooseIf you select an Album and press OK, the Track 62 MP3 PlaybackSelection screen will appear. Press K or L to select Track you want to play, then press Play B o or OKMP3 Track Selection MP3 Display Information, MP3 Track SelectionMP3 Display Information Random MP3 Playback Random MP3 Playback, Programmed MP3 PlaybackProgrammed MP3 Playback Press o or p to select a Track, then press OK toPress DVD, then press DISPLAY/STATUS/EXIT dur On-Screen DisplaysIng playback Press DISPLAY/STATUS/EXIT againPress the Number 2 button to select Display Display SettingsSETUP. The SET-UP screen will appear Press K or L to select an item, then press OK Display Settings cont’dPress Setup to remove the menus SETUP. The Setup screen appears Language SettingsPress DVD, then press Setup Press Setup to remove the menusLanguage Code Language Settings cont’dPress o or p to select a setting, then press OK SETUP. The Setup screen will appear Audio SettingsSRS TruSurround on Black Level SettingsTruSurround Setting Care and Maintenance, Specifications Cable Box/DBS Output Channel 03 or GlossaryRemote control will not operate the DVD/VCR DVD/VCR has no powerThere is no picture in DVD mode Helpful HintsHelpful Hints cont’d VCR will not perform a timer recording Power FailureMotor cylinder rotates even when tape playback is stopped VCR will not record a TV programCleaning the Video Heads Line Input modeYou can not insert a video cassette You can not remove the tapePhilips, P.O. Box 520890, Miami, FL 33152 402 Limited WarrantyTo obtain a replacement product from Philips Limited Warranty cont’dExchange Fee + Sales Tax = Total Payment, if applicableAutomatic Information Index
Top Page Image Contents