Philips VR810BPH Setting the Controller to Operate a DBS cont’d, 7Wait for a few seconds

Page 54

54 Setting the Controller to Operate a DBS (cont’d)

6

Press the PLAY 8 or STOP 9 button to set the two-digit code for your DBS (see list below), then press the OK/STATUS button.

7Wait for a few seconds.

SAT/

CBL/DBS TV VCR

SELECT CODE NUMBER OF YOUR DBS RECEIVER

40

DID DBS RECEIVER

CHANGE TO CHANNEL 205?

A YES

NO

SELECT: 89	CONFIRM:OK
END: MENU

DBS CODES

MAGNAVOX DBS	42, 43
RCA DBS	40
SONY DBS	41	6-8
7		6-8

Wait for a few seconds.

•If the DBS changes to channel 205, go to step 8.

•If the DBS doesn’t change to channel 205, press the PLAY 8 or STOP 9 button to select NO, then press the OK/STATUS but- ton. Repeat steps 6-7, using a different code for your brand (if available).

•If the DBS does not respond to any of the codes, press the MENU button to remove the menu. DBS RECEIVER CON- TROL IS OFF will appear on the screen briefly.

8

Press the PLAY 8 or STOP 9 button to select YES, then press the OK/STATUS button. “DBS RECEIVER CONTROL IS ON” will appear for five seconds. “AS A RESULT AUTO CLOCK WILL BE TURNED OFF” may appear on the screen also.

VCR/TV POWER SMARTPICTURE

QUICK PROGRAMMING

1— +* + 2 ABC + 3 DEF

START		STOP	DATE
4 GHI - 5 JKL - 6 MNO
VPS/PDC		DAILY	WEEKLY
7PQRS		8 TUV	9WXYZ
SPEED		DBS/SAT
ALT		0	CLEAR
-	STILL/SLOW			+
	..........		..........
REW				FF
		PLAY

STOP

VOL OK/STATUS CH

MENU

TIMER

TURBO AUDIO/ SKIP TAPE

TIMER MUTE SEARCH MANAGER

JOG/SHTL	REC /OTR
REV	FWD

Helpful Hint

•If your DBS does not respond to the code at step 7, the Controller will not change channels at the DBS during a timer recording. In this case, you must select the channel to be recorded at the DBS before a timer recording begins. Enter the DBS output channel at step 3 on page 40. Leave the DBS on for the timer recording. Details are on page eight.

Image 54

Contents VR810BPH Dear Philips product owner For Customer UseIntroduction FeaturesSafety Precautions Picture QualityTable of Contents Using the Remote Control Before Using Your VCRPutting Batteries in the Remote Control VCR Maintenance/Video Head CleaningHookups without a Cable Box Disconnect the antenna or cable from your TVHookups without a Cable Box cont’d Antenna Or CableConnections Cable signal RF coaxial cableHookups with a Cable Box/Direct Broadcast System Recording/Viewing Any Channel2RF coaxial cable Recording One Channel/Watching AnotherWith this connection TV’sTurning on Your VCR Menu shown below will appearTurn on the TV Turning on Your VCR cont’d Automatic Channel Setup Press the VCR button, then press the Menu buttonAutomatic Channel Setup cont’d Adding/Deleting ChannelsSelected channel Channels are set up. Details are on Setting the ClockManual Clock Setting To make corrections, follow stepsSetting the Clock cont’d Setting the Clock cont’d Time Zone SelectionManual PBS Channel Selection Automatic PBS Channel Selection CBL/DBS VCR VCR/TV Power Daylight-Savings TimeLanguage Selection Press the Play 8 or Stop 9 button to select LANPress the Menu button Turbo Timer indicators VCR Display Panel VHS Indicator VR1010BP onlyTape Speed Timer Light Lights Line Input Mode Remaining Tape Time IndicatorFront Panel Rear Panel Remote Control Buttons SAT/CBL/DBS Button Turbo Timer ButtonTimer Button ALTernate ChannelSetting the Remote Control to Operate a TV Repeat stepTurn on your Satellite Receiver/Cable Box/DBS Find the code for yourIf on Screen Mode is set to on or Press the Play 8 or Stop 9 button to select onPlaying Playback options and features are on pagesWhen you insert a tape, tape manag Read and follow the steps below to play a tapePress the VCR button VCR records in a preset volumeRecording Appear on the display panelVHS Recording VR1010BP only VHS ET VR1010BP only Recording One Channel/Watching Another VCR light will disappear from the display panelChannels are set up. Details are on pages One-Touch RecordingStarting an OTR Record Link Setting Up the VCR Plus+ Programming System ChannelsCall Letters Examine the lists 2onTimer Recording with the VCR Plus+ Programming System To check your timer recordings, see If you forget to turn off the VCRQuick Programming Channels are programmed. Details are on pagesInstructions continue on Tape SpeedsQuick Programming cont’d Helpful Hint Turbo Timer Current channel number will appear on the display panel. To1Insert a tape into the VCR Indicates a Weekly recording Checking, Editing, or Clearing Timer RecordingsProgram Review Indicates a Daily recordingPress the OK/STATUS button to select the program Or, to cancel the timer recording, press the Clear buttonProgram Overlap Warning Information about the chosen program will appearTimer Recording Speed Setting Follow the steps below to set Timer REC Speed to AutoRerecording Tape Duplication VCR 1 will play your tape. Insert a prerecorded tape in VCRAudio equipment CD player etc Audio cableBlinks and appears on the VCR display panel Make sure the video tape’s record tab is intactConnecting the Controller Connect the Cable signal toCable Box/DBS Controller Connect the Controller Setting the Controller to Operate a Cable Box Make sure the clock is set. You must set the clock manuallySetting the Controller to Operate a Cable Box cont’d Wait for a few secondsSetting the Controller to Operate a DBS Channel other thanWill learn your DBS code Setting the Controller to Operate a DBS cont’d 7Wait for a few secondsMulti-Channel Television Sound System Receiving a Stereo BroadcastReceiving a Second Audio Program Multi-Channel Television Sound System cont’d Record the program as usual. Details are onHi-Fi Stereo Tape Playback Video Stabilizer Or special effects playbackSmartPicture Digital Studio Picture Control To provide the highest possible picture qualityTo set Dspc to on or OFF, follow these steps Index Search Press the Stop 9 button to cancel a Skip SearchSearch Options Skip SearchViewing a Still Picture Playback OptionsForward and Reverse Searching Viewing a Slow Motion PictureViewing a Picture in Slow to Fast Motion Will lightInsert a tape that was recorded with this VCR Tape ManagerFind a Title Press the VCR button, then press the TapePress the Play 8 or Stop 9 button to select Check Tape Manager cont’dCheck Memory Check Memory screen appearsEdit Title If you don’t see the tape title or proTape titles may have up to 10 characters Entering Characters Selected programSorting by Tape Number FootballSorting by Date Sorting by Category As follows, for exampleFind Blank Space Review the tape portion to make sure it is blankDeleting Tape or Program Information If you want to erase more information, repeat stepsYou can disable the Tape Manager if you don’t want to use it CL will blink intermittently on the display panel When Child Lock is activatedChild Lock CL will disappear from the display panelBlue Background To set Blue Background to on or OFF, follow these stepsAutomatic Operation Features Glossary Helpful Hints Helpful Hints cont’d Limited Warranty Video Cassette Recorder or PlayerPayment Amount Limited Warranty cont’dTo obtain a replacement product from Philips Check or money order Account numberSpecifications Automatic Remote controlTimer Cable boxSupplied Accessories